517530
32
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
32
User’s manual
EN
Problem Cause Remedies
“Safety Lift” appears on the display Front body sensor does not work
Makes sure the upper body is positioned correctly. If the
problem persists, contact your nearest authorised service
centre
“Sync error” appears on the display The robot’s receiver does not recognise the signal
Turn the robot off and then turn it back on again. If the problem
persists, contact your nearest authorised service centre
“Too high grass” or “Blade Error”
appears on the display
Cutting blade damaged Replace the blade with a new one (see “Blade Replacement”)
Cutting blade fouled (tape, cords, plastic
fragments, etc.)
Stop the robot safely (see “Robot Safety Stop”)
Warning - Caution
Use protective gloves to prevent injury.
Unclog the blade
The robot was started too close to obstacles
(less than a distance of m) or in the presence of
obstacles (fallen branches, forgotten objects, etc.)
Stop the robot safely (see “Robot Safety Stop”)
Remove the obstacles and restart the robot (see “Start-up and
manual stopping of the robot (in closed areas)”)
Electric motor failure
Have the motor replaced or repaired by your nearest
authorised service centre
Too high grass
Increase the cutting height (see “Adjustment of cutting height”)
Carry out a preliminary cutting of the area with a normal
lawnmower
The remote control does not work
Programming error
Correctly program the remote control (see “Programming
Mode”)
The LED of the remote control does not light up Remove the batteries and replace them
“Safety Lift” appears on the display
Sensor indicating the presence of the body is not
positioned correctly
Remove the hood, makes sure it is correctly inserted in the
front slot
“Watchdog error” appears on the
display
The internal “software safety” system is enabled
Turn the robot off and on. If the problem persists, contact your
nearest authorised service centre
“Tilt” appears on the display
The robot is located on a level that is higher than
the allowed limits
Mark off the area that is too steep
The robot is located on a level that is lower than
the allowed limits
Check that the charging station is positioned on a at surface.
Turn the robot off and on while in the charging station and try
again. If the problem persists, contact your nearest authorised
service centre
(C)
The led ( c
) does not
turn on
No power supply
Make sure the power supply unit is correctly connected to the
power outlet
Interrupted fuse
Have the fuse replaced by your nearest authorised service
centre
The LED
(C) of the
transmitter
is on
Interrupted perimeter wire
Stop the robot safely (see “Robot Safety Stop”). Disconnect
the power plug from the power supply unit. Join the perimeter
wire
PARTS REPLACEMENT
RECOMMENDATIONS FOR REPLACING PARTS
Important
Replace and repair any parts according to the manufacturer’s instructions, or contact the service centre if these operations
are not included in the manual.
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ZCS 9L2BL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ZCS 9L2BL in de taal/talen: Engels als bijlage per email.

De handleiding is 10,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van ZCS 9L2BL

ZCS 9L2BL Gebruiksaanwijzing - Nederlands - 56 pagina's

ZCS 9L2BL Gebruiksaanwijzing - Nederlands - 33 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info