478506
6
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
Page 4 VL-1000 Operating Manual
connections labeled TX GND on the rear panel
of the transceiver; do not, however, use the
transceiver’s P
TT jack, as it was designed for
PTT input (via a footswitch, etc.), not for am-
plifier control.
Automatic Amplifier Tune-Up
If you connect the supplied control cable be-
tween the transceiver’s P
TT or REMOTE jack and
the VL-1000’s BAND-DATA 2 jack, the trans-
ceiver will automatically transmit when you
press the amplifier’s front panel F SET key
(make sure that the M
ODE switch of the trans-
ceiver is set to CW, RTTY, or some other con-
tinuous mode, and set the D
RIVE or RF PWR
control fully clockwise, if you want to perform
antenna tuning). To accomplish this function,
pin 11 of the BAND-DATA 2 jack closes the
transceiver’s P
TT or REMOTE jack to ground, thus
placing the transceiver in the transmit condi-
tion.
Automatic Amplifier Tune-Up
using FT-1000MP Transceiver
When using the VL-1000 in conjunction with
the FT-1000MP transceiver, the front panel F
SET key may be used to initiate an automatic
tuning procedure for the amplifier. In order to
accomplish this, Menu Item 7-9 on the FT-
1000MP must be set to “KEYER ” (which is its
default value), and a control cable must be con-
nected between the FT-1000MP’s R
EMOTE jack
and the VL-1000’s BAND-DATA 2 jack. The
required wiring for this cable is shown below.
Installation
Antenna Connections
As many as four HF or 50 MHz antennas
may be connected to the rear panel Antenna
jacks, labeled ANT 1 ~ ANT 4. The antenna to
be used on a particular band will be memo-
rized once you make the selection manually
via the front panel ANT switch. See the “Op-
eration” section of this manual for more de-
tails.
ALC Connections
The VL-1000 provides negative-going ALC,
which provides a negative voltage to the ex-
citer which begins to appear when sufficient
drive power from the exciter is being received;
the voltage becomes of greater (negative)
magnitude if the drive is increased, so as to
prevent overdrive of the amplifier. The voltage
range provided from the VL-1000 is 0 to 10
Volts DC, and this is compatible with all Yaesu
transceivers as well as many exciters of other
manufacture. At 1000 Watts of output power,
the typical voltage generated for use with
Yaesu transceivers is about 4 V DC.
The ALC cable must be connected between
the transceiver and VL-1000 to prevent over-
drive of the amplifier, and especially to facili-
tate the proper operation of the protection cir-
cuitry if sudden antenna system problems
should cause the SWR to rise to dangerous
levels.
PTT Connections
These jacks, labeled PTT 1 and PTT 2, ac-
cept T/R control signals from your exciter.
Grounding the center pin of one of these PTT
jacks will cause the amplifier to be placed in
the “Transmit” mode.
These jacks utilize a positive voltage (5V
DC) at very low current (10 mA maximum), so
they are compatible with most open-collector
NPN transistor amplifier control circuits in mod-
ern transceivers. Mechanical relays may also
be used, so long as they are “floating” con-
tacts that do not apply a voltage to the VL-
1000’s PTT jacks. On Yaesu transceivers, use
either the transistor or relay (Normally Open)
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu VL-1000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu VL-1000 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info