674747
79
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
Page 77
FT
DX
1200 OPERATING MANUAL
The powerful CW operating capabilities of the
FT
DX
1200
permit operation using an electronic keyer paddle, a “straight
key”, or a computer-based keying device.
SETUP FOR STRAIGHT KEY
(
AND STRAIGHT KEY EMULATION
)
OPERATION
Before starting, connect your key lines) to the front andor rear panel
KEY
jacks). Be sure the
[
BK-IN
]
button is
turned off for now.
1. 3ress the
[
MODE
]
button to engage CW operation.
The “
USB CW
icon will appear in the display. The
MONI
” icon will appear in the TFT display and the
CW monitor is activated.
A
DVICE:
If you press and hold the
[
MODE
]
button, you will
engage the “CW 5everse” mode, whereby the “op-
posite” sideband injection is used, compared to the
“normal” sideband. The “
LSB CW
icon will ap-
pear in the display if you select CW 5everse.
. 5otate the 0ain Tuning 'ial knob to select the de-
sired operating freTuency.
3. 3ress the
[
BK-IN
]
button to engage automatic acti-
vation of the transmitter when you close the CW key.
The “
BK-IN
” icon will appear in the TFT display.
A
DVICE:
When you close your CW key, the transmitter
will automatically be activated, and the CW car-
rier will be transmitted. When you release the
key, transmission will cease, and after a brief
delay, receive will be restored. The delay time is
user-programmable per the discussion on page
83.
$s shipped from the factory, the
FT
DX
1200
T;
5; system for CW is configured for “Semi-
break-in” operation. However, using 0enu item
063 CW BK-IN
”, you may change this setup
for full break-in QS.) operation, whereby the
switching is Tuick enough to hear incoming sig-
nals in the spaces between the dots and dashes of
your transmission. This may prove very useful
during contest and traf¿c handling operations.
4. 2peration using your CW key may now proceed.
A
DVICE:
You may adjust the CW sidetone audio level setting
of 0enu item “
036 MONITOR LEVEL
”.
To adjust the 0onitor level
1) $ctivate the 021I circuitry, if necessary.
) 3ress and hold in the
[
MONI
]
button for one
second to enter the 0enu item “
036 MONITOR
LEVEL
”.
3) 3ress the
[
SELECT
] button
.
4) While keying, rotate the
[
VFO-B/CLAR
]
knob
or press the
S
T
button) to adjust the monitor
level.
) When you are satisfied with the setting, press
the
[
SELECT
]
button, then press the
[
MENU
]
button to save the new setting and exit to normal
operation.
If you set the
[
BK-IN
]
button to 2ff, you may prac-
tice sending CW with the sidetone only, without hav-
ing the signal go out over the air.
If you reduce power via the 0enu item
177 TX
MAX POWER
”, the $LC meter reading will increase
this is normal and does not indicate any problem
whatsoever because increased $LC voltage is being
used to lower the power).
TERMINOLOGY:
Semi-break-in
This is a pseudo-”V2;” mode used on CW, whereby the closure of the CW key will engage the transmitter, and
release of the key will allow the receiver to recover after a short delay. 1o signals will be heard during the spaces
between dots and dashes unless the sending speed is extremely slow).
Full break-in
Full break-in also known as “Full QS.”) involves very fast switching between transmit and receive, incoming
signals may be heard between the dots and dashes as you send them. This allows you to hear a station that sud-
denly starts transmitting on your freTuency, while you are in the midst of a transmission.
CW MODE OPERATION
[
MONI
]
Button
[
BK-IN
]
Button
[
MODE
]
Button
79

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FTDX1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FTDX1200 in de taal/talen: Engels als bijlage per email.

De handleiding is 14,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info