674747
31
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
Page 29FT
DX
1200 OPERATING MANUAL
REAR PANEL
ANT 1/2 Jacks
Connect your main antennas) here, using type-0
3L-) connectors and coaxial feed lines. The in-
ternal antenna tuner affects only the antennas) con-
nected here, and only during transmission.
Warning!
7KH95)YROWDJH#:ȍLVDSSOLHGWR
the TX RF section of the transceiver while trans-
mitting. Do not touch the TX RF section while
transmitting.
DC IN Jack
This is the 'C power supply connection for the
transceiver. Use the supplied 'C cable to connect di-
rectly to a 'C power supply, which must be capable
of supplying at least 3 $ #13.8 V'C.
GND
Use this terminal to connect the transceiver to a good
earth ground, for safety and optimum performance.
Use a large diameter, short braided cable for making
ground connections, and please refer to page for
other notes about proper grounding.
To prevent damage from lightning, atmo-
spheric electricity, electrical shock, etc., be
certain to provide a good earth ground.
μ-TUNE Jacks
These jacks are used to connect the optional 5F
Tuning .it, signal in and signal out.
ROT Jack
This covered 6-pin 0I1I-'I1 -ack accepts a cable
to connect to a Y$(SU
G-800DXA
-1000DXA/
-2800DXA
$ntenna 5otator listed models are cur-
rent as of early 013). You may control the antenna
a]imuth rotation and rotation speed) using the Func-
tion buttons on the front panel.
LINEAR Jack
This 10-pin output jack provides band selection data,
which may be used for control of optional accesso-
ries such as the
VL-1000
Solid-state Linear $mpli-
¿er.
TUNER Jack
This 8-pin output jack is used for connection to the
FC-40
(xternal $utomatic $ntenna Tuner.
RTTY/DATA Jack
This 6-pin inputoutput jack accepts $FS. input
from a Terminal 1ode Controller T1C) or an op-
tional interface unit it also provides ¿xed level 100-
mV #600 2hms) receiver audio output, and FS.
keying line.
PTT Jack
This 5C$ input jack may be used to provide manual
transmitter activation using a footswitch or other
switching device. Its function is identical to the
[
MOX
]
button on the front panel. The same line is
available at the
RTTY/PKT
jack for T1C control.
2pen-circuit voltage is  V'C, and closed-circuit
current is m$.
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FTDX1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FTDX1200 in de taal/talen: Engels als bijlage per email.

De handleiding is 14,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info