674747
19
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
Page 17FT
DX
1200 OPERATING MANUAL
FRONT PANEL CONTROLS & SWITCHES
PHONES Jack
$ 14-inch, 3-contact jack accepts either monaural or
stereo headphones with - or 3-contact plugs. When
a plug is inserted, the loudspeaker is disabled.
N
OTE:
When wearing headphones, we recommend that you
turn the $F Gain levels down to their lowest settings
before turning power on, to minimi]e the impact on
your hearing caused by audio “pops” during switch-
on.
MIC Jack
This 8-pin jack accepts input from a microphone uti-
li]ing a traditional Y$(SU HF transceiver pinout.
[
ANT
]
Switch
3ressing this switch selects the
ANT 1
or the
ANT
2
connector on the rear panel, and allows convenient
antenna switching at the press of a button. The se-
lected antenna jack is indicated on the .ey Function
'isplay shown in the TFT 'isplay.
A
DVICE:
The $1T jack may be enabled to use as a receive
only antenna, using the 0enu item “
033 ANT2 SET-
TING
”. See page 114.
[
IPO
]
(
INTERCEPT POINT OPTIMIZATION
)
Switch
This button may be used to set the optimum front
end characteristics of the receiver circuit for a very
strong signal environment. $vailable selections are
$03 1 low distortion amplifier), $03 -stage
low-distortion 5F amplifier), or I32 bypasses the
front end 5F amplifier). The selected receiver 5F
amplifier appears in the I32 column of the .ey
Function 'isplay on the display.
[
ATT
]
Switch
This button selects the degree of attenuation, if any,
to be applied to the receiver input.
$vailable selections are ±6 dB, ±1 dB, ±18 dB, or
2FF. The attenuation level appears in the $TT col-
umn of the .ey Function 'isplay on the display.
A
DVICE:
The $ttenuator may be used in conjunction with the
[
IPO
]
button to provide additional signal reduction
when an extremely strong signal is being received.
[
R.FLT
]
(
ROOFING FILTER
)
Switch
This button selects the bandwidth of the receiver ¿rst
IF 5oo¿ng Filter. $vailable selections are 3 kH], 6
kH], 1 kH], or $uto.
The selected bandwidth appears in the 5.FLT column
of the .ey Function 'isplay on the TFT display.
A
DVICE:
The $UT2” selection mode selects the optimum
bandwidth of the 5oo¿ng ¿lter for the reception
mode. In this case, the selected bandwidth in
the 5.FLT column of the .ey Function 'isplay
glows green The unselected choices glow Blue).
Because the roofing filter is in the first IF, the
protection it provides against interference is Tuite
significant. When set to $UT2, the SSB band-
width is 6 kH], CW, 5TTY and '$T$, the band-
width is 3 kH], while $0 and F0 is 1 kH].
[
NB
]
Switch
This button turns the IF 1oise Blanker on and off.
3ress this button momentarily to reduce short-dura-
tion pulse noise.
$vailable selections are 21, 2FF, or 1BW 21. The
attenuation level appears in the 1B column of the
.ey Function 'isplay on the display.
[
AGC
]
Switch
This button selects the $GC characteristics for the
receiver. $vailable selections are F$ST, 0I', SL2W
and 2FF, or $UT2. The selected $GC characteris-
tic appears in the $GC column of the .ey Function
'isplay on the TFT display.
3ress the
[
AGC
]
button repeatedly to select the de-
sired receiver-recovery time constant. 3ress and hold
in the
[
AGC
]
button for one second to disable the
$GC for testing or weak-signal reception).
A
DVICE:
The $UT2” selection mode selects the charac-
teristic of the $GC for the reception mode. The
selected $GC characteristic will glow green in
the $GC column of the .ey Function 'isplay,
unselected characteristics glow Blue).
The $ttenuator may be used in conjunction with
the
[
IPO
]
button to provide two stages of signal
reduction when an extremely strong signal is be-
ing received.
If the $GC receiver-recovery time is set to “2ff”
by pressing and holding in the
[
AGC
]
button, the
S-meter will no longer deÀect. $dditionally, you
will likely encounter distortion on stronger sig-
nals, as the IF ampli¿ers and the following stages
are probably being overloaded.
[
MOX
]
Switch
3ressing this button engages the 3TT 3ush to Talk)
circuit to activate the transmitter the icon in the
L(' indicators area illuminates and the “
MOX
” icon
will appear in the TFT display). It must be turned off
the icons will disappear) for reception. This button
replicates the action of the 3ush to Talk 3TT) switch
on the microphone. When engaging the
[
MOX
]
but-
ton, or otherwise causing a transmission to be start-
ed, be certain you have either an antenna or 0-2hm
dummy load connected to the selected $ntenna jack.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FTDX1200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FTDX1200 in de taal/talen: Engels als bijlage per email.

De handleiding is 14,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info