674740
142
Verklein
Vergroot
Pagina terug
1/154
Pagina verder
Page 140 FT-991 OperaTing Manual
installation of optional accessories
Setup the FT-991
The optional
FC-40
Automatic Antenna Tuner provides automatic tuning of a coaxial line to present nominal 50-ohm
impedance to the
FT-991
s ANT jack.
Before operation can begin, the
FT-991
microprocessor must be setup to accommodate the
FC-40
automatic tuner. This
is done using the Menu Mode:
Fc-40 externAl AutoMAtic AntennA tuner
(
For Wire AntennA
)
1. Press the
MENU(SETUP)
button to enter the Menu
mode.
2. Rotate the
MULTI
knob to select the Menu Item “
143
TUNER SELECT
”.
3. Touch
[
SELECT
]
on the LCD, then rotate the
MULTI
knob to select “
EXTERNAL
”.
MULTI Knob
MENU(SETUP) Button TUNE Button
81: %
670'4'5'%6.
'5'%6.
+
 /:6:/# 219'4 
0
/+
6'40#.



4. Touch
[
ENTER
]
on the LCD to save the new setting.
670'4'5'%6. ':6'40#.
81: %
'5'%6.
 /:6:/# 219'4 
/+


5. Press the
MENU(SETUP)
button or touch
[
BACK
]
on the LCD to exit to normal operation.
Operation
1. Press the
TUNE
button briefly to activate the
Automatic Antenna Tuner.
2. The “
TUNER
” icon will appear in the TFT display.
3. Press and hold the
TUNE
button for one second
to begin automatic tuning. The transmitter will be
engaged, and the “
TUNER
” icon will blink while
tuning is in progress.
4. Tuning will stop automatically when a low SWR is
achieved. You may Press the
TUNE
button while
tuning is in progress, to cancel the automatic tuning.
5. To disable the Automatic Antenna Tuner, press the
TUNE
button briey again.
note:
r
Be sure to connect a good earth ground to the GND
terminal of the
FC-40
.
r
The carrier signal transmits continuously while
tuning is in progress. Please monitor the operating
frequency before beginning the tuning process. Be
sure you are not interfering with others who may
already be using the frequency.
r
It is normal to hear the sound of the relays while
tuning is in progress.
r
If the impedance cannot be matched by the
FC-40
better than 2:1, and the “
HI-SWR
” icon blinks, the
microprocessor will not retain the tuning data for that
frequency, as the
FC-40
presumes that you will want
to adjust or repair your antenna system to correct the
high SWR condition.
142

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-991 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-991 in de taal/talen: Engels als bijlage per email.

De handleiding is 30,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info