674740
121
Verklein
Vergroot
Pagina terug
1/154
Pagina verder
Page 119FT-991 OperaTing Manual
Data (psk) operation
exAMple oF dAtA coMMunicAtionS device
Software Settings
note:
There are many good Data Mode Operating Software
programs available on the internet. Each of these pro-
grams will have their own Setup instructions, therefore
to assist you, the following, while general in nature is
common to most software setup.
COM PORT Settings
To start set the Com Port setting to the Enhanced
Driver. If there is a problem switch to the Standard
Driver.
PTT Settings
Set the PTT to RTS on DTR off.
SOUNDCARD
a. At the software Soundcard setting, set to USB CO-
DEC AUDIO
b. At the software Soundcard Volume setting increase
the volume to about 70% to start.
Advice:
If the soundcard volume setting is to low the radio
will not switch to Transmit.
DATA MODE
(PSK, OLIVIA, CONTESTIA, RTTY etc.)
FT-991 Settings
1. Press the
MODE
button, and then touch the corre-
sponding key on the LCD to select the DATA-USB
operating mode. The
D-U
” icon appears in the dis-
play.
Advice:
USB is the conventional mode for Digital (not
RTTY) transmission on all bands, however some us-
ers may be using LSB.
2. Press the
MENU(SETUP)
button. The Menu list
will appear in the display.
3. Rotate the
MULTI
knob to nd Menu item
062
”,
063
”, “
070
”, “
071
” or “
072
”.
4. Touch
[
SELECT
] on the LCD.
5. Rotate the
MULTI
knob to set these Menu item as
shown below.
Menu Function Setting
062 DATA MODE PSk
063 PSk TONE
Adjust for desired
center frequency.
070 DATA IN SELECT MIC
071 DATA PTT SELECT RTS
072 DATA PORT SELECT USB
6. Touch
[
ENTER
]
on the LCD, then press the
MENU(SETUP)
button or touch
[
BACK
]
on the
LCD to exit to normal operation.
note:
All other SSB and DATA settings remain at their de-
fault.
Connect a USB Cable from the FT-991 USB port
and your computer
Advice:
Before connecting the USB cable you must down load
the SCU-17 Drivers. The Drivers can be found on the
FT-991
FILES page at the Yaesu Web page, www.
yaesu.com. Once the Drivers have been installed con-
nect the USB cable to the computer and then to the ra-
dio. At your computers Device Manager you will nd
a Standard Driver and Enhanced Driver installed.
Computer Settings
Soundcard
At your Computer Control Panel Sound set your
Speaker Audio default to USB AUDIO CODEC.
COM PORT
Check your Com Port assignments at your Computer’s
Device Manager to be sure you have the Enhanced
and Standard Drivers. Make a note of the Com Port
numbers assigned.
Software Settings
note:
There are many good Data Mode Operating Software
programs available on the internet. Each of these pro-
grams will have their own Setup instructions, therefore
to assist you, the following, while general in nature is
common to most software setup.
COM PORT Settings
To start set the Com Port setting to the Enhanced
Driver. If there is a problem switch to the Standard
Driver.
PTT Settings
Set the PTT to RTS on DTR off.
SOUNDCARD
a. At the software Soundcard setting, set to USB CO-
DEC AUDIO
b. At the software Soundcard Volume setting increase
the volume to about 70% to start.
Advice:
If the soundcard volume setting is to low the radio
will not switch to Transmit.
121

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-991 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-991 in de taal/talen: Engels als bijlage per email.

De handleiding is 30,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info