478504
19
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
Page 17FT-950 OPERATING MANUAL
[
MOX
]
Switch
Pressing this button engages the PTT (Push to Talk)
circuit, to activate the transmitter (the LED inside this
button will glow red). It must be turned off (the red
LED will be off) for reception. This button replicates
the action of the Push to Talk (PTT) switch on the mi-
crophone. When engaging the
[
MOX
]
button, or oth-
erwise causing a transmission to be started, be certain
you have either an antenna or 50-Ohm dummy load
connected to the selected Antenna jack.
[
VOX
]
Switch
This button enables automatic voice-actuated transmit-
ter switching in the SSB, AM, and FM modes. While
activated, the LED inside this button glows red. The
controls affecting VOX operation are the Menu items
114 TGEN V GAIN”, “115 TGEN VOX DLY”, and
116 TGEN ANTI VOX”. By proper adjustment of these
controls, hands-free voice-actuated operation is pos-
sible.
[
MONI
]
(
Monitor
)
Switch
This button enables the transmit monitor in all modes.
While activated, the “ ” icon appears in the dis-
play. The Monitor audio level may be adjusted by turn-
ing the
[
MONI
]
knob.
ADVICE:
When using headphones, the Monitor function is very
helpful while adjusting the Parametric Equalizer or
other voice quality adjustments. The voice heard in the
headphones represents the transmitted audio qualities.
[
PROC
]
(
Processor) Switch
This button enables the Parametric Microphone Equal-
izer and Speech Processor for SSB/AM transmission.
When the Parametric Microphone Equalizer is acti-
vated, the “ ” icon appears in the display. When
the Speech Processor is activated, the “ ” and
” icons appear in the display. Adjustment of
the Processor level is accomplished via the Menu item
109 TGEN PROCLVL”.
ADVICE:
The Speech Processor is a tool for increasing the
average power output through a compression tech-
nique. However, if the Processor level is advanced
too far, the increase in compression becomes
counter-productive, as intelligibility will suffer. We
recommend that you monitor the sound of your sig-
nal using the Monitor (with headphones).
When the optional Data Management Unit (DMU-
2000) is connected, you may use the Audio Scope/
Oscilloscope page to help you adjust the setting of
the compression level of the Speech Processor for
optimum performance using your voice and micro-
phone.
[
SPOT
]
Switch
This button turns on the CW receiver spotting tone; by
matching the SPOT tone to that of the incoming CW
signal (precisely the same pitch), you will be “zero
beating” your transmitted signal on to the frequency of
the other station.
The offset tone frequency will be indicated in the fre-
quency display area of the display while this button is
pressed.
[
BK-IN
]
Switch
This button turns the CW break-in capability on and
off. While CW break-in is activated, the “ ” icon
appears in the display.
[
KEYER
]
Switch
This button toggles the internal CW keyer on and off.
While activated, the “ ” icon appears in the dis-
play. The Keyer sending speed is adjusted via the front
panel’s
[
SPEED
]
knob and the CW Hang Time is ad-
justed via the Menu item “044 A1A DELAY”.
[
AGC
]
Switch
This button selects the AGC characteristics for the re-
ceiver. Available selections are FAST, MID, SLOW,
or AUTO. The “AGC” icon will change according to
the AGC characteristics selected.
Press the
[
AGC
]
button repeatedly to select the de-
sired receiver-recovery time constant. Press and hold
in the
[
AGC
]
button for two seconds to disable the
AGC (for testing or weak-signal reception).
ADVICE:
The Attenuator may be used in conjunction with
the
[
IPO
]
button to provide two stages of signal
reduction when an extremely strong signal is being
received.
If the AGC receiver-recovery time is set to “Off”
by pressing and holding in the
[
AGC
]
button, the
S-meter will no longer deflect. Additionally, you
will likely encounter distortion on stronger signals,
as the IF amplifiers and the following stages are
probably being overloaded.
FRONT PANEL CONTROLS & SWITCHES
19

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Yaesu-FT-950

Zoeken resetten

  • Bij het opstarten knippert TX. Ontvangst doet het, maar zenden niet. Wie heeft een oplossing? Gesteld op 15-4-2024 om 14:09

    Reageer op deze vraag Misbruik melden
  • Hoe sluit ik een digibox (MMSTV) aan op een FT950? Gebruikte voorheen een FT575GX2 . Deze had 3 tulpstekkertjes. Audio in audio uit en PTT ontvangst werkt goed en de zender schakelt ook in. Audio signaal klinkt niet zoals het hoort. Gesteld op 28-7-2023 om 19:00

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-950 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-950 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info