478500
23
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 21FT-897D OPERATING MANUAL
OPERATION
LSB USB CW CWR
AMFMDIGPKT
MODE
MODE SELECTION
Press either the MODE
(
)
or MODE
(
)
key to move
among the eight settings for the operating modes, respec-
tively.
where “CWR” is “CW-Reverse,” using the opposite side-
band from the “default” BFO injection sideband (in most
cases, the default injection sideband is on the “USB” side);
“DIG” is an AFSK-based Digital mode, set up per Menu
Mode No-038
[
DIG MODE
]
; and “PKT” represents either
1200 or 9600 bps FM packet.
You can set VFOa and VFOb to different modes
in the same band, allowing you to have a
“Phone” VFO and a “CW” VFO, for example.
ADJUSTING THE AUDIO VOLUME LEVEL
Rotate the AF knob to set a comfortable listening level.
When operating in the “DIG” or “PKT” modes, you may
set the AF knob to any comfortable setting, or even all the
way off, because the output from the DATA jack is a fixed-
level audio signal.
Start with the AF knob set fully counter-clock-
wise, especially when using FM (the back-
ground noise on FM can be surprisingly loud)!
ADJUSTING THE RF GAIN AND SQUELCH
The SQL/RF Gain control is configured differently, depend-
ing on the country to which the FT-897D has been exported.
In the U.S. version, the default function of this control is
“RF Gain.” The configuration of the SQL/RF Gain control
is set via Menu Mode No-080
[
SQL/RF GAIN
]
; see page 62
for details.
If your transceiver is configured for “RF Gain” use, rotating
this control fully clockwise in the SSB/CW/Digital modes
will provide best sensitivity. To reduce the receivers RF
Gain somewhat, rotate this control counter-clockwise
slightly. You will observe an increasing number of bars on
the S-meter as you rotate the RF Gain control counter-clock-
wise; this indicates increasing AGC voltage, which is caus-
ing the front-end gain to be reduced. In the FM and Packet
modes, this control will automatically be set to “Squelch,”
even though the setting of Menu Mode No-080
[
SQL/RF
GAIN
]
is “RF Gain.” But if you set it this way, the SQL/RF
control has no effect on FM.
More accurately, this should say:
In the FM and Packet modes, with “RF Gain” selected, the
FT-897D goes into an “Auto Squelch” mode, with the
Squelch level being preset at the factory.
If this control is configured for “SQL” operation, the FT-
897Ds RF Gain will be set for maximum sensitivity in all
modes, and the SQL/RF Gain control will function solely
as a Squelch control. In this case, rotate the SQL/RF Gain
control to the point where the background noise is just si-
lenced; this will provide the best sensitivity to weak signals,
while keeping the receiver quiet when no signal is received.
The LED just above the Main Dial will glow Green when
the squelch is opened by an incoming signal or noise.
Battery consumption is significantly reduced if
the receiver is squelched, as the audio ampli-
fier stage is shut off when the receiver is muted.
BATT-B
BATT-A
MODE
BATT-B
BATT-A
AF
BATT- B
BATT- A
SQL/RF
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info