478500
20
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 18 FT-897D OPERATING MANUAL
INPUT Jack
This is the DC power supply connection for the trans-
ceiver, used when operating the transceiver with an ex-
ternal power supply. Use the supplied DC cable to con-
nect this jack to the car battery or DC power supply,
which must be capable of supplying at least 22A @ 13.8
VDC. For base station operation, the optional FP-30
External AC power supply may be attached to the bot-
tom of the transceiver and connect the output pigtail of
the FP-30 to this jack.
GND Terminal
For best performance and safety, this Ground lug may
be connected to a good earth ground using a short, heavy,
braided cable.
CAT/LINEAR Jack
This 8-pin mini-DIN jack is used for connection to the
FC-30 External Automatic Antenna Tuner or ATAS-100/
-120 Active-Tuning Antenna System. It is also used for
interfacing to a personal computer for control of the trans-
ceiver using the CAT system, and for interconnection
to the VL-1000 Linear Amplifier.
ACC Jack
This 3.5-mm 3-pin jack accepts external ALC (Automatic
Level Control) voltage from a linear amplifier on the tip
connection, and accepts a “Transmit Request” command
on the ring connection. The main shaft is the ground re-
turn.
The “TX Request” connection, when shorted to ground,
puts the FT-897D into the transmit mode, and sends out
a steady CW carrier, for linear amplifier or manual an-
tenna tuner adjustment.
REAR PANEL CONNECTORS
KEY Jack
This 3.5-mm, 3-pin jack is used for connection to a CW
keyer paddle or a straight key.
EXT SPKR Jack
This 3.5-mm, 2-pin jack provides variable audio output
for an external speaker. The audio output impedance at
this jack is 4 ~ 16 and the level varies according to
the setting of the front panel’s AF control.
CAT
/TUNER
+13.8V
BAND C
RESE
T
TX INH
RX D
TX D
TX GND
GND
LINEAR
+13.8V
BAND C
BAND D
TX INH
BAND B
BAND A
TX GND
GND
DATA Jack
This 6-pin, mini-DIN jack accepts AFSK input from a
Terminal Node Controller (TNC); it also provides fixed-
level Receiver Audio Output, Push-To-Talk (PTT),
Squelch Status, and ground lines.
DATA
DATA OUT
1200bps
DATA OUT
9600bps
SQL
GND
PTT
DATA IN
144/430 MHz Antenna Jack
Connect your 144 and/or 430 MHz antenna’s 50 co-
axial cable to this M-type (“SO-239”) connector.
HF/50 MHz Antenna Jack
Connect your HF and/or 50 MHz antenna’s 50 co-
axial cable to this M-type (“SO-239”) connector.
SIGNAL GND
EXT ALC GND
TX REQ
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info