478500
10
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 8 FT-897D OPERATING MANUAL
ANTENNA CONSIDERATIONS
The antenna systems connected to your FT-897D transceiver
are, of course, critically important in ensuring successful
communications. The FT-897D is designed for use with any
antenna system providing a 50 resistive impedance at the
desired operating frequency. While minor excursions from
the 50 specification are of no consequence, the power
amplifiers protection circuitry will begin to reduce the power
output of there is more than a 50% divergence from the speci-
fied impedance (less than 33 or greater than 75 , corre-
sponding to a Standing Wave Ratio (SWR) of 1.5:1).
Two antenna jacks are provided on the rear panel of the FT-
897D. The “HF/50 MHz ANT” jack is used for HF and 50
MHz, while the “144/430 MHz ANT” jack is used for 144
MHz and 430 MHz.
Guidelines for successful base and mobile station installa-
tions are shown below.
Mobile Antenna Installations
Mobile antennas for the HF bands, with the possible excep-
tion of those designed for 28 MHz, display very high “Q”
due to the fact that they must be physically shortened, then
resonated using a loading coil. Additional system bandwidth
may be realized using the Yaesu FC-30 Automatic Antenna
Tuner, which will present a 50 impedance to your trans-
ceiver on the 1.8 ~ 50 MHz bands so long as the SWR on
the coaxial line connected to the FC-30 is below 3:1.
On the VHF and UHF bands, coaxial line losses increase so
rapidly in the presence of SWR that we recommend that all
impedance matching to 50 be performed at the antenna
feedpoint.
Yaesu’s Active-Tuned Antenna System (ATAS-100/-120)
is a unique HF/VHF/UHF mobile antenna system, which
provides automatic tuning when used with the FT-897D.
See page 39 for full details on the ATAS-100/-120.
For VHF/UHF weak-signal (CW/SSB) operation, remem-
ber that the antenna polarization standard for these modes is
horizontal, not vertical, so you must use a loop or otherwise
horizontally-polarized antenna so as to avoid cross-polar-
ization loss of signal strength (which can be 20 dB or more!).
On HF, signals propagated via the ionosphere develop mixed
polarizations, so antenna selection may be made strictly on
mechanical considerations; vertical antennas are almost al-
ways utilized on HF for this reason.
Base Station Antenna Installations
When installing a “balanced” antenna such as a Yagi or di-
pole, remember that the FT-897D is designed for use with
an (unbalanced) coaxial feedline. Always use a balun or other
balancing device so as to ensure proper antenna system per-
formance.
Use high-quality 50 coaxial cable for the lead-in to your
FT-897D transceiver. All efforts at providing an efficient
antenna system will be wasted if poor quality, lossy coaxial
cable is used. Losses in coaxial lines increase as the fre-
quency increases, so a coaxial line with 0.5 dB of loss at 7
MHz may have 6 dB of loss at 432 MHz (thereby consum-
ing 75% of your transceivers power output!). As a general
rule, smaller-diameter coaxial cables tend to have higher
losses than larger-diameter cables, although the precise dif-
ferences depend on the cable construction, materials, and
the quality of the connectors used with the cable. See the
cable manufacturers’ specifications for details.
For reference, the chart below shows approximate loss fig-
ures for typically- available coaxial cables frequently used
in HF installations.
Loss in dB per 30 m (100 feet)
for Selected 50-ohm Coaxial Cables
Loss
Cable Type 1.8 MHz 28 MHz 432 MHz
RG-58A 0.55 2.60 >10
RG-58 Form 0.54 2.00 8.0
RG-8X 0.39 1.85 7.0
RG-8A, RG-213 0.27 1.25 5.9
RG-8 Form 0.22 0.88 3.7
Belden 9913 0.18 0.69 2.9
7/8” “Hardline” <0.1 0.25 1.3
Loss figures are approximate; consult cable manufacturers
catalogs for complete specifications.
Always locate antennas such that they can never come in
contact with outdoor power lines in the event of a catastrophic
support or power-pole structural failure. Ground your an-
tennas’ support structure(s) adequately, so as to dissipate
energy absorbed during a lightning strike. Install appropri-
ate lightning arrestors in the antenna coaxial cables (and
rotator cables, if rotary antennas are used).
In the event of an approaching electrical storm, disconnect
all antenna lead-in, rotator cables, and power cables com-
pletely from your station if the storm is not immediately
in your area. Do not allow disconnected cables to touch the
case of your FT-897D transceiver or accessories, as light-
ning can easily jump from the cable to the circuitry of your
transceiver via the case, causing irreparable damage. If a
lightning storm is in progress in your immediate area, do
not attempt to disconnect the cables, as you could be killed
instantly if lightning should strike your antenna structure or
a nearby power line.
If a vertical antenna is utilized, be certain that humans and/
or pets and farm animals are kept away both from the radiat-
ing element (to prevent electrical shock and RF exposure
danger) and the ground system (in the event of an electrical
storm). The buried radials of a ground-mounted vertical
antenna can carry lethal voltages outward from the center of
the antenna in the event of a direct lightning strike.
INSTALLATION
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info