478466
54
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
52 FT-7900R OPERATING MANUAL
The ARTS feature uses DCS signaling to inform both parties when you and another ARTS-
equipped station are within communications range. This may be particularly useful during
Search-and Rescue situations, where is important to stay in contact with other members of
your group.
Both stations must set up their DCS codes to the same code number, then activate their
ARTS feature using the command appropriate for their radio. Alert ringers may be activated,
if desired.
Whenever you push the PTT switch, or every 25 seconds
after ARTS is activated, your radio will transmit a signal
which includes a (subaudible) DCS signal for about one
second. If the other radio is in range, the beeper will sound
(if enabled) and the display will show “
IN.RNGIN.RNG
IN.RNGIN.RNG
IN.RNG” as opposed
to the out of range display “
OUT.RNGOUT.RNG
OUT.RNGOUT.RNG
OUT.RNG” in which ARTS op-
eration begins.
Whether you talk or not, the polling every 25 seconds will continue until you de-activate
ARTS. Every 10 minutes, moreover, you can have your radio transmit your callsign via CW,
so as to comply with identification requirements. When ARTS is de-activated, DCS will also
be deactivated (if you were not using it previously in non-ARTS operation).
If you move out of range for more than one minute (two pollings), your radio will sense that
no signal has been received, three beeps will sound, and the display will revert to “
OUT.RNGOUT.RNG
OUT.RNGOUT.RNG
OUT.RNG”.
If you move back into range, your radio will again beep, and the display will change back to
the “
IN.RNGIN.RNG
IN.RNGIN.RNG
IN.RNG” indication.
During ARTS operation, it is not possible to change the operating frequency or other set-
tings; you must terminate ARTS in order to resume normal operation. This is a safety feature
designed to prevent accidental loss of contact due to channel change, etc. Here is how to
activate ARTS:
Basic ARTS Setup and Operation
1. Set your radio and the other radio(s) to the same DCS code number, per the discussion
on page 29.
2. Press and hold in the
[
S.SCH
(
ARTS
)]
key for 1/2 sec-
ond. You will observe the “
OUT. RNGOUT. RNG
OUT. RNGOUT. RNG
OUT. RNG” display on the
LCD. ARTS operation has now commenced.
3. Every 25 seconds, your radio will transmit a “polling” call to the other station. When that
station responds with its own ARTS polling signal, the
display will change to “
IN.RNGIN.RNG
IN.RNGIN.RNG
IN.RNG” to confirm that the other
station’s polling code was received in response to yours.
4. Press and hold in the
[
S.SCH
(
ARTS
)]
key for 1/2 second to exit ARTS operation and
resume normal operation of the transceiver.
ARTS
: AUTO RANGE TRANSPONDER SYSTEM
54

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-7900R bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-7900R in de taal/talen: Engels als bijlage per email.

De handleiding is 2,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info