813079
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Page 2 / 4
© Wodtke GmbH Tübingen. All rights reserved. Subject to change without notice. Month of issue 03/2011 Art. No. 950 325
Display Messages
Display
message Explanation
“Standby dot”; appliance has been switched off manually via I/O key. Press the I/O key to switch on the stove. The stove
does not respond to external controllers when in standby mode.
ON ON start signal (appears briefly when you switch on the stove)
The stove has been started. After briefly showing the programme being used it enters the TEST phase.
OFF OFF stop signal (appears briefly or alternates with “A” for 4 minutes when you switch off the stove)
The stove has been switched off and after going through phases A1 – A4 enters fan after-run phase G OFF.
B1
001
This is the programme and programme version (appears for some seconds during start-up).
B1 = programme 3 – 9 kW; B2 = programme 3 – 11 kW; B3 = programme 3 – 13 kW; B4 = programme 3 – 13 kW
001 = programme version 1; 002 = programme version 2; flashes alternately with TEst (see below).
TE
st
TEST phase (appears after starting the stove)
Checks all stove functions; flue gas exhaust flap cycle starts. If no error is found during the test phase, the stove enters the
preheating programme (A). This display message flashes alternately with B1 – B4.
A
1
Indicates that the Preheating Programme is running and its duration in minutes (which is variable).
The stove begins to feed pellets into the firebox, the ignition element starts, and the ignition process is monitored (after
successful completion of the preheating phase the stove enters the heating programme (H); example: A1 minute 1 of
preheating programme; A8 minute 8 of preheating programme…
AI
...
Preheating programme in + number of minutes (flashes alternately with G OFF)
The stove is still in G OFF. However, the stove has registered that the I/O key has been pressed again. It is indicating that it will
automatically resume operation in x minutes (after completion of G OFF). example: AI 11 = preheating will start in 11 minutes.
H
... Heating programme + set thermal output in kW
The stove is in heating mode, example: H 8.0 = heating programme running at 8 kW.
H.M
3.0
Heating programme internal minimum + thermal output in kW
Î The heat generated by the stove is not being fed into the heating system / is not required. Thermal output has been reduced
to a minimum (3 kW) by an internal controller because boiler water temperature TW > 80°C. The stove will re-enter the heating
programme (H) when the temperature has dropped sufficiently. Note: Don’t confuse H.M (internal) with HM (no dot – external).
R
-15
Cleaning programme (R) + remaining number of minutes (flashes alternately with G OFF)
After 4 hours continuous operation the stove starts an automatic cleaning cycle of 15 minutes duration. First the stove switches
to fan after-run (R-15 and G OFF flash alternately), then the ash is removed. Note: The stove restarts automatically after
completion of the cleaning programme R.
G
OFF
Fan after-run (=stove switches off and ash is removed; 15 minutes duration)
The fan runs for another 15 minutes (the remaining pellets burn down, the flue gas is carried off, ash is removed).
Note: Only when G OFF does not flash alternately with R, AI, HE OFF or TW OFF does the stove go into standby when fan
after-run is over. In all other cases the stove restarts automatically after fan after-run is over.
TW
OFF
Heat exchanger is cut off by a thermal switch (Î heat is not fed into the heating system)
The stove switches off via an internal control mechanism because boiler water temperature TW > 85 °C. The stove restarts
automatically after the temperature has dropped sufficiently.
RA
... Cleaning prompt (appears briefly)
The stove needs cleaning; example: RA 0.1 = cleaning overdue since 0.1 t pellets.
WA
... Service prompt (appears briefly)
The stove needs servicing. example: RA 0.1 = servicing overdue since 0.1 t pellets.
PL
AUF
Fuel hopper open
The hinged cover of the fuel hopper is open. If it is open for longer than 3 minutes without interruption while the stove is in
operation (display shows Test, A, H, HM, H.M, HE, G OFF), this will produce an error shutdown (PL Err).
AL
AUF
Ashpit door open
The ashpit door is open in standby mode. If it is open for longer than 3 minutes without interruption while the stove is running
(display shows Test, A, H, HM, H.M, HE, G OFF), this will immediately cause an error shutdown (AL Err).
Only open the ashpit door when the stove is not running!
FT
AUF
Firedoor open
The firedoor is open in standby mode. If the firedoor is opened while the stove is in operation (display shows Test, A, H, HM,
H.M, HE, G OFF), the stove will immediately produce an error shutdown (FT Err).
Only open the firedoor when the stove is not running!
PE
res
Fuel level below reserve line
The fuel hopper is almost empty and should be refilled immediately. If the display message PE res appears for longer than 5
minutes the stove will produce an error shutdown (PE Err).
“Function currently not available”
This display message appears when the function you have called up is currently not available (e.g. switching off the appliance
while an automatic routine such as grate cycle/ash removal is still running.
HE
...
Externally controlled heating programme (only possible with external modulating controller)
The stove is being operated at the indicated output level via an external modulating controller;
example: HE 7.2 = heating programme running at 7.2 kW via an external controller
HM
3.0
Heating programme running at minimum level (only possible with external controller)
The stove has been set to its minimum output level (3 kW) via an external controller (MIN/MAX input).
Note: Don’t confuse H.M (dot between H and M – internal) with HM (no dot – external).
HE
OFF Heating programme switched off via external controller (only possible with external controller)
The stove has been switched off via an external controller (via input ON/OFF or BUS or TC1).
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Wodtke Ivo.safe S5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Wodtke Ivo.safe S5 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Wodtke Ivo.safe S5

Wodtke Ivo.safe S5 Gebruiksaanwijzing - Deutsch - 80 pagina's

Wodtke Ivo.safe S5 Gebruiksaanwijzing - Français - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info