484211
4
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
P.06
P.07
Installation Instructions
3.Loosen the lock nut with a spanner and turn the foot by hand until it contacts the floor.
Hold the foot with one hand and fasten the nut against the cabinet with a spanner.
4.Press the four top corners again to check that the feet have been adjusted properly.
If the machine is still unstable repeat steps 2 and 3.
5.Put a solid cylinder (e.g. pop can) on the top cover of the washing machine in the left,
right, front and back positions. If it rolls then the machine is not level. The rolling direction
is the direction of the ground surface. The two legs in this direction need to be raised
at the same time until the washing machine is level. Once the machine is level ensure
that all the nuts are locked tight.
Connect the inlet pipe as indicated in the figure.
This machine only has a cold water inlet.
The water inlet pipe should be connected to
a ¾” threaded water tap
1. Connect the end of the pipe, with an elbow,
to the water inlet valve on the rear of the machine.
Tighten the nut clockwise.
2. Connect the other end of the inlet pipe to the
water tap.
Turn on the tap and ensure that there is no water
leakage.
There are three possible ways to connect the outlet hose to a suitable drain.
1. Position the outlet hose into a sink.
Inlet Pipe Connection
Installing the Inlet Pipe
Installing the Outlet Hose
Unpacking the Washing Machine
Unpack the washing machine and check that there is no transport damage.
Ensure that all the items (as shown on page 5) are included in the enclosed bag.
If there is any damage to the washing machine during transportation or any items
are missing, please contact your retailer immediately.
The packaging materials of this machine may be dangerous to children.
Please dispose of them properly in accordance with the local regulations.
Please do not throw the packaging materials away with general household waste.
Before using the washing machine the transport bolts
must be removed from the rear of the machine.
Please take the following steps to remove the bolts:
1. Loosen all 4 bolts with a spanner and remove them.
2. Stop the holes with the transport hole plugs provided.
3. Keep the transport bolts for future use.
The washing machine must be installed in a location with the following characteristics:
-Rigid, dry and level surface (if not level please refer to the following section “Adjusting the Feet”)
-Avoid direct sunlight
-Room temperature above 0°C
-Away from sources of heat
Ensure that the washing machine is not standing on the power cord.
Do not install the washing machine on a carpeted floor.
1.When positioning the washing machine please check
that all the feet are fully screwed into the cabinet. If not,
please turn them to their original positions and tighten
the nuts with a spanner.
2.After positioning the washing machine, press all four
corners on the top of the washing machine in sequence.
If the washing machine is not stable when being pressed,
this foot should be adjusted.
Disposal of the Packaging Materials
Removing the Transport Bolts
Selecting the Location
Adjusting the Feet
Installation Instructions
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw White Knight WM105M bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van White Knight WM105M in de taal/talen: Engels als bijlage per email.

De handleiding is 0,69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info