650531

Whirlpool DLCE 81469 Handleiding

2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
CONSUMPTION DATA
Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the
energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting
of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.
T
he programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load.
**** After programme and spinning with maximum selectable spin speed, in default programme setting.
Programme
Tempe-
rature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
Approx. remaining
moisture content (%)****
without “Rapid” with “Rapid” 1200 rpm 1400 rpm
Mixed 40 4.0 50 0.40 1:00 - 58 55
Cotton 95 8.0 82** 2.50 2:40 -
58 55
Cotton 60 8.0 57 1.30 2:20 1:35
Cotton 40 8.0 75 0.85 3:15 1:15
Synthetics 60 3.0 48** 1.05 2:15 0:55
40 35
Synthetics 40 3.0 44 0.60 2:15 0:55
Delicates 40 1.5 65 0.60 0:50 -
Delicates 30 1.5 65 0.40 0:46 -
Wool/ Handwash 40 1.0 50 0.50 0:40 -
Wool/ Handwash cold 1.0 50 0.10 0:35 -
Jeans 40 4.0 52 0.45 1:30 1:10
White 40 8.0 75 0.65 2:20 -
Light colours 40 4.0 60 0.45 1:20 -
Dark 40 4.0 40 0.55 1:40 1:15
Speed 15’ 30 3.0 25 0.15 0:15 -
AquaEco 40 3.0 19 0.45 1:00 -
Cotton * 60 8.0 52 0.67 4:00 -
53 53 Cotton * 60 4.0 38 0.66 3:10 *** -
Cotton * 40 4.0 38 0.50 3:10 *** -
- the sensor technology adapts water, energy and programme duration to the size of your wash load.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Load the laundry, close the door and turn the programme selector
to the desired programme; the “Start/Pause” indicator blinks. The
temperature and spin speed shown on the display can be altered by
pressing the “Temperature” button or the “Spin” button.
If you do not use the “Dosing Aid”, add detergent now.
Your washing machine is designed to save energy. After the end of a
programme, or when a programme is selected but not yet started, the
washing machine will therefore switch off automatically after about a
quarter of an hour. To switch the washing machine on again, turn the
programme selector to “O” and afterwards to the desired programme
again.
SELECT ANY DESIRED OPTION
When the combination of programme and additional option(s) is
not possible, the indication switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Colours 15°” button
• Saves energy used for water heating while maintaining a good
wash result.
• Supports colour maintenance when washing coloured laundry.
• Recommendable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
• Not selectable for Cotton 70 - 95°C.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft water,
washing baby linen and helps people with allergies.
“Rapid” button
• Enables quicker washing by shortening the programme duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 70 - 95°C.
“Prewash” button
• Adds a prewash cycle to the wash programme selected; prolongs
the programme by about a quarter of an hour.
• Recommended for heavily soiled laundry (e.g. with sand or
granular dirt).
• Do not use liquid detergent for the main wash when activating the
“Prewash” option.
“Soil level” button
• Adapts the programme duration to the soil level of your laundry.
Also influences the detergent quantity recommendation when
using the “Dosing Aid” button.
= lightly soiled - = normally soiled - = heavily soiled.
Not all soil levels are selectable for each programme.
“Spin” button (incl. “Rinse hold”)
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If you select spin speed “0”, the final spinning is cancelled and
the water is drained out only. However, intermediate spin phases
remain during the rinse.
• If you select “Rinse hold”, the laundry remains in the last rinse
water without progressing to the final spin cycle, to avoid creasing
and prevent colours from changing. To activate the “Rinse hold”,
press the “Spin” button repeatedly until the “Rinse hold” symbol on
the display lights up.
- The wash programme stops to “Rinse hold” when the “Rinse
hold” symbol on the display blinks; the light of “Start/Pause”
button also blinks.
PROGRAMME START
Open the tap and press the “Start/Pause” button . The indicator next to
the “Start/Pause” button lights up.
CHILD LOCK
Activating the child lock prevents children from starting a wash cycle or
changing the settings of a running programme. The child lock cannot
be activated or deactivated when the programme selector is in the “O”
position. To activate the child lock:
• Turn the programme selector to a programme position, or run a
programme as usual.
• Press the 2 buttons marked with the key symbol simultaneously
for at least 3 seconds. A key-like symbol will shortly appear on the
display to indicate that the child lock is active.
Any time you try to change a programme setting with active child
lock, the display will briefly show the key-like symbol. The programme
setting cannot be changed anymore. The only change possible is to
switch the washer off by turning the programme selector to the “O”
position.
To deactivate the child lock:
• Press again the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds.
FAILURE INDICATION
In case of any failures or irregularities, consult the “Troubleshooting
Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
“Service” : failure or malfunction of an electrical component.
“Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning.
PROGRAMME END
The “Door open” indicator lights up, and the display shows “End”.
After about a quarter of an hour, the washing machine will switch
off completely to save energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
DETERGENT OVERDOSAGE INDICATION
The symbol will light up at the end of the programme if you used too
much detergent. Use less detergent next time. If the symbol lights up
and the display shows “Fod”, too much foam interrupted the wash
process; refer to the “Troubleshooting Guide” in your Instructions for
Use.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause” button to pause the programme. The light
blinks.
2. Select the new programme, temperature, any options and another
spin speed if you want.
3. Press the “Start/Pause” button again. The new programme
continues at the same position where the previous programme was
interrupted. Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset/Drain” button cancels a programme before the end.
• Press and hold the “Reset/Drain” button for a few seconds; an
animation appears on the display. The water is drained out; it may
last some time until you can open the door.
- To terminate the “Rinse hold“ by spinning the laundry, press
“Start/Pause” - the laundry will be spun with the default spin
speed. You can also select another spin speed with the „Spin“
button before you start the spin cycle by pressing “Start/Pause”.
- To terminate the “Rinse hold“ by draining the water without
spinning, press the “Spin“ button until spin speed “0“ appears on
the display; then press “Start/Pause” to start the draining.
- Do not leave the laundry to soak for too long in the “Rinse hold”
(especially silk).
SET CYCLE END
With this function you can postpone your programme to complete
at a later time: press the button to select in how many hours the
programme shall be finished. Thus, it allows you to have your laundry
ready at a particular time and to profit from more favorable energy
rates during the night, for example. Do not use liquid detergent when
activating “Cycle end” option.
• The time until the “Cycle end” can be selected in full hour time
segments (1 to 24 h). When you press the button, the shortest
possible time will be displayed; keep on pressing the button to
loop through all the available times. To remove it again, keep on
pressing the button until you see the value “0:00”.
• When you have selected the desired time until the “Cycle end”,
press “Start/Pause” - the countdown will begin.
• During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.). If the
modifications prolong the programme duration so that it overruns
the originally set time until the “Cycle end”, the programme will
start immediately.
• Sometimes the programme may finish before the selected time
until the “Cycle end” has expired (e.g. for small loads). In this case,
the washing machine will tumble the laundry regularly to keep
it fresh, until the selected “Cycle end” time has expired. During
tumbling, the display will show an animation. The tumbling phase
can be stopped at any time either by pressing any button or by
rotating the programme selector; the animation will stop and the
door will unlock in about 1 minute as indicated on the display.
DETERGENT DOSING RECOMMENDATION
With the “Dosing Aid” button, you can make your washing machine
indicate you the recommended detergent quantity for your wash load,
depending on the soil level selected and the size of the load.
• Helps to save detergent and protect the environment and also
sensitive skin by avoiding detergent overdosing.
• Before you use this function, you must adapt the washing machine
to the dosing amounts which are recommended for the detergents
you use. Also check if your region’s water hardness corresponds
with the water hardness level “soft” of your washing machine - if
not adapt it.
• Select programme, options and cycle end BEFORE using the
“Dosing Aid” button.
For any details, refer to the separate “Dosing Aid” Instructions for Use.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show
the the door can be opened. As long as a wash programme is running,
the door remains locked and must on no account be forced open. In
case you have an urgent need to open it during a running programme,
refer to “Reset” a running programme before the end”.
ECO MONITOR
The “Eco Monitor“ gives you a rough feedback about the power
consumption of the programme setting you selected. As soon as you
turn the programme selector to any programme, the
“
Eco Monitor“ is on.
The indicator on the left is to show that the “Eco Monitor“ is active.
The four indicators next to it show the degree of consumption: the less
power your programme setting is forecasted to consume, the less
indicators will light up. This depends on the programme, temperature
and options selected, and also on the size of the wash load. For that
reason, the forecasted degree of power consumption may adapt when
the washing machine detects the wash load.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Whirlpool DLCE 81469 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Whirlpool DLCE 81469 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Whirlpool DLCE 81469

Whirlpool DLCE 81469 Gebruiksaanwijzing - English - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info