Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
“Rinse hold” button
• The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• It is particularly useful if you want to postpone spinning
to a later time, or if you want to drain only.
• The wash programme stops to “Rinse hold” when the
“Rinse hold” indicator on the display blinks. The “Start/
Pause” indicator blinks as well.
Terminate the “Rinse hold” option:
• Press the “Start/Pause” button; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme and
press the “Start/Pause” button.
“Spin” button
• Every programme has a predefined spin speed.
• Press the button to set different spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
SET CYCLE END
With this function you can postpone your programme
to complete at a later time: press the button to select in
how many hours the programme shall be finished. Thus,
it allows you to have your laundry ready at a particular
time and to profit from more favorable energy rates during
the night, for example. Do not use liquid detergent when
activating “Cycle end” option.
• The time until the “Cycle end” can be selected in full
hour time segments (1 to 24 h). When you press the
button, the shortest possible time will be displayed;
keep on pressing the button to loop through all the
available times. To remove it again, keep on pressing
the button until you see the value “0:00”.
• When you have selected the desired time until the
“Cycle end”, press “Start/Pause” - the countdown will
begin.
• During the countdown, you can still modify the
programme setting (select or deselect options, change
spin speed etc.). If the modifications prolong the
programme duration so that it overruns the originally
set time until the “Cycle end”, the programme will start
immediately.
• Sometimes the programme may finish before the
selected time until the “Cycle end” has expired (e.g.
for small loads). In this case, the washing machine will
tumble the laundry regularly to keep it fresh, until the
selected “Cycle end” time has expired. During tumbling,
the display will show an animation. The tumbling
phase can be stopped at any time either by pressing
any button or by rotating the programme selector; the
animation will stop and the door will unlock in about 1
minute as indicated on the display.
ECO MONITOR
The „Eco monitor“ gives you a rough feedback about the
power consumption of the programme setting you selec-
ted. As soon as you turn the programme selector to any
programme, the „Eco monitor“ is on.
The indicator on the left is to show that the „Eco monitor“
is active. The four indicators next to it show the degree of
consumption: the less power your programme setting is
forecasted to consume, the less indicators will light up.
“Clean+” button
• Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Use with maximum load.
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together
with your detergent (only use powder detergent
with this option). Respect the manufacturer’s dosing
instructions.
• May prolong the programme by up to 15 minutes
• Appropriate for use of stain removers and bleaches on
oxygen basis. Chlorine or perborate bleaches must
not be used!
“Prewash” button
• Adds a prewash cycle to the wash programme
selected; prolongs the programme by about a quarter
of an hour.
• Recommended for heavily soiled laundry (e.g. with
sand or granular dirt).
• Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
allergies.
“Easy ironing” button
• Reduces creasing by an increased water quantity and
a very gentle spin.
LOAD LAUNDRY, ADD DETERGENTS
AND SELECT THE PROGRAMME
Load the laundry, add detergent and turn the programme
selector tothe desired programme and temperature; the
“Start/Pause” indicator blinks. The spin speed shown on
the display can be altered by pressing the “Spin” button
If you do not start the programme soon after having
made your choice, the washing machine will switch off
automatically after about a quarter of an hour. To switch
the washing machine on again, turn the programme
selector to “O” and afterwards to the desired programme
again.
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication switch off
automatically.
“Colours 15°” button
• Saves energy used for water heating while maintaining
a good wash result.
• Supports colour maintenance when washing coloured
laundry.
• Recommendable for lightly soiled laundry without
stains.
• Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
• Not selectable for Cotton 95°C.
“Rapid” button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 95°C.
This depends on the programme, temperature and options
selected, and also on the size of the wash load. For that
reason, the forecasted degree of power consumption may
adapt when the washing machine detects the wash load.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the door can be opened. As long as a wash
programme is running, the door remains locked and must
on no account be forced open. In case you have an urgent
need to open it during a running programme, refer to
“Reset” a running programme before the end”.
PROGRAMME START
Open the tap and press the “Start/Pause” button . The
indicator next to the “Start/Pause” button lights up.
When the laundry load is detected or the programme
duration is updated, the display shows an animation.
FAILURE INDICATION
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water
”Service” : failure or malfunction of an electrical
component
”Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during
spinning.
PROGRAMME END
The “Door open” indicator lights up, and the display shows
“End”. After about a quarter of an hour, the washing
machine will switch off completely to save energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not add
detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the end.
• Press and hold the “Reset” button for a few seconds;
an animation appears on the display. The water is
drained out; it may last some time until you can open
the door.
- the sensor technology adapts water, energy and programme duration to the size of your wash load.
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the
energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default
setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption
data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Whirlpool AWOC 9253 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Whirlpool AWOC 9253 in de taal/talen: Engels als bijlage per email.
De handleiding is 1,3 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
