Whirlpool is a registered trademark of Whirlpool USA
Load the laundry, add detergent and turn the programme selector to
the desired programme and temperature; the “Start/Pause”
indicator blinks. The spin speed shown on the display can be
altered by pressing the “Spin” button
When a combination of programme/option or option/option is
not possible, the indicator switches off automatically. Unsuitable
combinations of options are deselected automatically.
“Prewash” button
•Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
•Recommended for heavily soiled laundry (e.g. with sand or
granular dirt).
•Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Rapid” button
•Enables quicker washing by shortening the programme duration.
•Recommendable for only lightly soiled laundry.
•Not selectable for Cotton 95°C.
“Clean +” button
•Choose this option if you use an in-wash additive for stain
removal (powder, for example “Vanish”) - it will optimize the
additive’s efficiency to get better wash performance and
stain removal.
•Use with maximum load.
•Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
•May prolong the programme by up to 15 minutes.
•Appropriate for use of stain removers and bleaches on oxygen
basis. Chlorine or perborate bleaches must not be used!
“Cold wash 15°” button
•Saves energy used for water heating while maintaining a
good wash result.
•Supports colour maintenance when washing coloured laundry.
•Recommendable for lightly soiled laundry without stains.
•Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
•Not selectable for Cotton 95°C.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very soft water
or for washing baby linen, and helps people with allergies.
“Easy ironing” button
•Reduces creasing by an increased water quantity and a very
gentle spin.
“Rinse hold” button
•The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and
prevent colours from changing.
•Particularly useful if you want to postpone spinning to a later
time, or if you want to drain only.
•The programme stops to “Rinse hold” at the time the “Rinse
hold” indicator on the display blinks. The “Start/Pause”
indicator blinks as well.
CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
without “Rapid”with “Rapid”
Mixed404.0480.501:00—
Cotton957.074**2.202:30—
Cotton607.0541.192:201:35
Cotton407.0660.752:051:15
Easy Care (Synthetics)403.0420.501:200:55
Delicates301.5600.400:46—
Wool/Handwash401.0450.550:40—
White407.0680.802:20—
Light colours404.0600.451:20—
Dark404.0400.551:401:15
EcoCotton*607.0540.844:00—
EcoCotton*603.5400.63 3:00***—
EcoCotton*403.5400.61 3:00***—
Speed 15303.0250.150:15—
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual
water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.
15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water
supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature.
Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options
or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
**To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.
***Automatic adaptation of programme duration after detection of wash load.
*Reference programmes for Energy Label.
LOAD LAUNDRY, ADD DETERGENT AND
SELECT PROGRAMME
SELECT ANY DESIRED OPTION
Terminate the “Rinse hold” option :
•Press the “Start/Pause” button ; the programme will
terminate automatically with the final spin cycle for the
present wash programme.
•If you do not wish to spin the clothes, turn the programme
selector to the “Drain” programme and press the “Start/
Pause” button to start draining.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If you select spin speed “0”, the final spinning is cancelled
and the water is drained out only. However, intermediate
spin phases remain during the rinse.
With this function you can postpone your programme to
complete at a later time: press the button to select in how many
hours the programme shall be finished. Thus, it allows you to have
your laundry ready at a particular time and to profit from more
favourable energy rates during the night, for example.
•The time until the “Cycle end” can be selected in full hour time
segments (1 to 24 h). When you press the button, the shortest
possible time will be displayed; keep on pressing the button
to loop through all the available times. To remove it again,
keep on pressing the button until you see the value “0:00”.
•When you have selected the desired time until the “Cycle
end”, press “Start/Pause” - the countdown will begin.
•During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.). If
the modifications prolong the programme duration so that it
overruns the originally set time until the “Cycle end”, the
programme will start immediately.
•Sometimes the programme may finish before the selected
time until the “Cycle end” has expired (e.g. for small loads). In
this case, the washing machine will tumble the laundry
regularly to keep it fresh, until the selected “Cycle end” time
has expired. During tumbling, the display will show an
animation. The tumbling phase can be stopped at any time
either by pressing any button or by rotating the programme
selector; the animation will stop and the door will unlock in
about 1 minute as indicated on the display.
Before starting and after end of a programme, the lamp lights to
show that the door can be opened. As long as a wash programme is
running, the door remains locked and must on no account be forced
open. In case you have an urgent need to open it during a running
programme, refer to “Reset a running programme before the end”.
The “Eco monitor” gives you a rough feedback about the power
consumption of the programme setting you selected.
As soon as you turn the programme selector to any programme, the
“Eco monitor” is on.
The indicator on the left is to show that the “Eco monitor” is active.
The four indicators next to it show the degree of consumption: the
less power your programme setting is forecasted to consume, the
less indicators will light up. This depends on the programme,
temperature and options selected, and also on the size of the wash
load. For that reason, the forecasted degree of power consumption
may adapt when the washing machine detects the wash load.
Open the tap and press the “Start/Pause” button . The
indicator next to the “Start/Pause” button lights up. When
the laundry load is detected or the programme duration is
adapted, the display shows an animation.
If one of the failure indicators blinks, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
“Service”: failure or malfunction of an electrical
component.
“Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning.
The “Door open” indicator lights up, and the display shows “End”.
1.Turn the programme selector to the “Off/O” position.
2.Close the water tap.
3.Open the door and unload the machine.
4.Leave the door ajar to allow the drum to dry.
1.Press the “Start/Pause” button to pause the
programme. The indicator blinks.
2.Select the new programme, temperature, any options and
another spin speed if you want.
3.Press the “Start/Pause” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
The “Reset” button cancels a programme before the end.
•Press and hold the “Reset” button for a few seconds; an
animation appears on the display. The water is drained; it
may last some time until you can open the door.
SET CYCLE END
“DOOR OPEN” INDICATOR
ECO MONITOR
lessmore
PROGRAMME START
FAILURE INDICATORS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
- the sensor technology adapts water, energy and programme duration to the size of your wash load.
Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.
Product:
Spelregels forum
Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:
lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;
Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.
Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.
Abonneren
Abonneer u voor het ontvangen van emails voor uw Whirlpool AWO 7648 bij:
nieuwe vragen en antwoorden
nieuwe handleidingen
U ontvangt een email met instructies om u voor één of beide opties in te schrijven.
Ontvang uw handleiding per email
Vul uw emailadres in en ontvang de handleiding van Whirlpool AWO 7648 in de taal/talen: Engels als bijlage per email.
De handleiding is 1,69 mb groot.
U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.
Uw handleiding is per email verstuurd. Controleer uw email
Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.
Er is een email naar u verstuurd om uw inschrijving definitief te maken.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken
U heeft geen emailadres opgegeven
Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.
Uw vraag is op deze pagina toegevoegd
Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.
