Handleiding Whirlpool AWE 5105 (pagina 2 van 2) (Engels)

539833

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

5019 300 00343

CONSUMPTION DATA

Whirlpool is a registered trademark of Whirlpool USA.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helping people

with allergies.

“Rinse Hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• This option is particularly recommended for

the “Synthetics”, “Daily load” and “Delicates”

programmes.

• It is useful if you want to postpone spinning to a later

time, or if you want to drain out only.

• If you select “Rinse Hold”, do not leave items to soak

for too long.

• As soon as the appliance stops in the rinse hold, the

“Rinse hold” lamp of the sequence indicator lights up

and the lamp next to the ““Start(Pause)” button

flashes.

Terminate the “Rinse Hold” option:

• Press the “Start(Pause)” button; the programme

will terminate automatically with the final spin cycle

for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain” programme

and press the “Start(Pause)” button.

“Spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

the rinse. The water is drained out only.

SELECT THE DESIRED OPTION(S)

When the combination of programme and additional

option(s) is not possible, the indication lights switch off

automatically. Unsuitable combinations of options are

deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Rapid” button

• Enables quicker washing by shortening the

programme duration.

• Recommendable for small loads or only lightly soiled

laundry.

1. Load the machine, close the drum doors and check

that they are properly locked.

2. Add detergent and eventual additives as described on

the front page and in your Instructions for use.

3. Close the lid.

4. Turn the programme selector to the desired

programme and temperature. The indication next

to the “Start(Pause)” button blinks. The indication

lamp of the predefined spin speed lights up. If you

do not start the programe soon after having made

your choice, the washing machine will switch off

automatically after about a quarter of an hour.

Switch on the washing machine again by turning the

programe selector back to „Off/O“ and then to the

desired programe.

PREPARATION OF THE WASH CYCLE

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer

to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Reference Programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a

wash programme is running, the lid remains locked and

must on no account be forced open. In case you have

an urgent need to open it during a running programme,

refer to “Cancel (Reset) a running programme before

the end”.

PROGRAMME START

PROGRAMME END

• The “Door open” indicator lights up. After about a

quarter of an hour, the washing machine will switch

off completely to save energy.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open for some time to allow the interior

of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start(Pause)” button to pause the

programme. The light blinks.

2. Select the new programme, temperature, any

options and another spin speed if you want.

3. Press the “Start(Pause)” button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add

detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The “Reset” button cancels a programme before the

end.

• Press the “Reset” button for at least 3 seconds. The

water is drained out; it may last a while until you can

open the lid.

START DELAY

The “Start delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper. Do not use liquid detergent when

activating the “Start delay”.

• Select programme, spin speed and options.

• Press the “Start Delay” button several times to

select a delay time of 1, 3, 6, 9 or 12 hours. The

corresponding indicator lamp lights up.

• Start the programme (see “Progremme Start”). The

indication next to the “Start delay” button lights up

and goes off when the programme starts.

• Once having pressed the “Start(Pause)” button,

the countdown of the time delay begins. When the

programme starts, the start delay indicator light

goes off and is replaced by the programme sequence

indication.

• After the “Start(Pause)” button has been pressed,

the number of hours preselected can be changed by

pressing again the “Start delay” button.

To cancel the “Start delay”

..before you press the ““Start(Pause)” button:

• Turn the programme selector to another position or

press the “Reset” button.

..after having pressed the “Start(Pause)” button:

• Press the “Reset” button for at least 3 second. The

start delay indicator light goes off.

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

without

“Rapid”

(kWh)

Approx. Programme Duration

(hours : minutes)

without “Rapid” with “Rapid”

Cotton 95 5.0 50* 1.70 2:05 1:55

Cotton 60 5.0 47 0.95 2:20 1:45

Cotton 40 5.0 47 0.64 2:05 1:30

Synthetics 60 3.0 50* 0.90 2:05 1:14

Synthetics 40 3.0 40 0.50 1:50 0:59

Delicate 40 1.5 50 0.55 0:45 -

Delicate 30 1.5 50 0.50 0:41 -

Daily load 40 3.0 40 0.45 1:00 -

Speed 15’ 30 3.0 30 0.15 0:15 -

Wool/Handwash 40 1.0 40 0.55 0:35 -

Wool/Handwash Cold 1.0 40 0:40 0:30 -

eCotton ** 60 5.0 47 0.89 2:45 -

eCotton ** 60 2.5 32 0.68 2:10 -

eCotton 40 5.0 47 0.65 2:00 -

eCotton ** 40 2.5 32 0.52 1:45 -

FAILURE INDICATIONS

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

Open the tap and press the “Start(Pause)” button.

The indication lamp next to the “Start(Pause)” button

lights up. The programme sequence indicator shows the

current programme phase, running from left to right

through Wash, Rinse, Spin/Drain. When the programme

phrase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

Power consumption in off-mode 0.11 W / in left-on mode 0.11 W.

Whirlpool AWE 5105 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Andere handleiding(en) van Whirlpool AWE 5105

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info