74451
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
TROUBLESHOOTING GUIDE
The hob does not work:
- Check for the presence of mains electrical power.
- Set the knob to
“0”
and switch on the hob again to
ensure that the fault has been remedied.
The hob does not turn off:
- disconnect the hob immediately by disconnecting the
power cable from the socket.
ACCESSORIES:
The glass cover can be ordered via the After Sales
Service, with the code: AMC 966 NB (New Black) AMC
966 MR (Mirror)
AFTER-SALES SERVICE
Before contacting After-Sales Service:
See if you can solve the problem yourself with the help
of the suggestions given in chapter “Troubleshooting
Guide”.
If after the above checks the fault persists, contact the
nearest After-sales Service.
Please give:
a brief description of the fault;
the type and exact model of the hob;
the service number (i.e., the number that follows the
word SERVICE on the rating plate, located under the
hob). The service number is also indicated on the
warranty booklet;
your full address;
your telephone number and area code.
If any repairs are required, please contact an
authorised
After-sales Service
(to guarantee that original spare parts
will be used and repairs carried out correctly).
Failure to comply with these instructions may
compromise the safety and quality of the product.
INSTALLATION
Recommendations
Important: Before any installation or maintenance
operation, disconnect the hob from the mains power
supply.
Electrical connections must be made before connecting
the appliance to the electricity supply.
Installation must be performed by a qualified technician
according to the manufacturer's instructions and current
local regulations.
After unpacking the hob, check that there has been no
damage during transport.
If in doubt, contact the
nearest dealer or Authorised After Sales Service.
Preparation of fitted cabinet
Perform all required cuts on the work top before
inserting the appliance. Carefully remove all chips or
residue which could impair efficient operation of the
appliance.
The hob must be recessed in a work top with a
thickness of min. 30 and max. 50 mm.
Insert a separator panel at a minimum distance of
20 mm from the bottom of the hob, so that it is not
accessible to the user.
If the hob is to be fitted above an oven, the latter must
be produced by the same manufacturer and equipped
with a cooling system.
Never place other materials between the hob and oven
(e.g. cross-members, insulation, etc.).
If the hob is to be installed next to a column unit, leave a
distance of at least 100 mm from the edge hob.
Make an opening in the worktop, observing the
dimensions specified.
Fit the seal supplied onto the hob (if not already
present), after carefully cleaning the application surface.
ASSEMBLY:
After having cleaned the perimeter surface, apply the
supplied gasket to the hob as shown in the figure.
Important:
before installing the hob, remove any plastic
protection film applied.
Ensure that the opening made in the worktop to house the
hob corresponds to the dimensional drawing specifications,
within the relative tolerances.
Never force the hob into the worktop.
For installation
, use the relative brackets and screws
supplied.
1.
Position the hob in the work top opening made respecting
the dimension indicated on first page.
NOTE:
The power supply cable must be long enough to
permit its upward extraction.
2.
To secure the hob, use the brackets
(A)
provided with it.
3.
Fit the brackets into the relevant bores shown by the
arrow and fasten them by means of their screws in
accordance with the tickness of the work top.
(see fig. 1).
Electrical connection
Regulations require that the appliance is earthed.
The electrical connection must be made by a qualified
technician according to the manufacturer's instructions
and current local regulations.
The installer is responsible for the correct electrical
connection of the appliance and the observance of the
relative safety standards.
To comply with directives governing safety, during
installation use a single-pole switch with a minimum gap
between contacts of 3 mm.
Do not use multiple plug adapters or extension leads.
After installation, electrical parts must not be accessible.
Connection to the electrical mains
Note:
the yellow/green earthing wire
(B)
must be
connected to the screw. If the power cable is not yet
connected:
strip approx. 70 mm of sheath from the power supply
cable
strip approx. 10 mm of sheath from the wires
Open the terminal board
(C)
by pressing the side tabs
by means of a suitable tool.
Insert the power cable
(D)
in clamp
(E)
and connect
the wires to the terminal board.
Close the terminal board cover.
After the electrical connection, insert the hob from the
above and secure on the fixing brackets as shown in
figure 1.
Declaration of conformity
This cooking hob is suitable for contact with foodstuffs,
and complies with EEC Directive 89/109.
This cooking hob has been designed to be used only for
cooking Any other use (such as heating a room) is
improper and dangerous
This cooking hob has been designed, constructed and
marketed in compliance with:
- safety requirements of EEC Directive
“Low voltage” 73/23;
- protection requirements of EEC Directive “EMC
89/336;
- requirements of EEC Directive 93/68.
Fig. 2
Fig. 3
Fig. 1
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Whirlpool AKT 310 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Whirlpool AKT 310 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Whirlpool AKT 310

Whirlpool AKT 310 Gebruiksaanwijzing - Nederlands - 2 pagina's

Whirlpool AKT 310 Gebruiksaanwijzing - Deutsch - 2 pagina's

Whirlpool AKT 310 Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info