Handleiding Whirlpool AKM 9010 (pagina 2 van 2) (Engels)

662535

Verklein

Vergroot

Pagina terug

1/2

Pagina verder

BEFORE USING THE COOKING HOB

Before use, remove:

- adhesives stuck on the hob;

- cardboard guards and protective plastic film;

- check whether the hob has been damaged during

transport. If in doubt, contact the After Sales Service.

Care and maintenance

• Clean the hob, when it is cool, after each use. This will

prevent the build-up of dirt and make cleaning easier.

• Use a clean cloth, absorbent kitchen wipes and washing

up liquid or a specific glass ceramic cleaner.

• Remove baked-on dirt with the special scraper tool

(if provided) and specific cleaning products.

• Any food spills should be cleaned off before they dry.

• Do not use abrasive products, chlorine-based cleaners,

oven-cleaner spray or pan scourers.

• The hob should be treated periodically with specific

products available from the shops, following the

manufacturer’s instructions.

TROUBLESHOOTING GUIDE

The hob does not work:

- Make sure that the power supply is on.

- Turn the hob off and on again, to make sure that the

problem has been solved.

- Make sure that the knob is not turned to “0”.

Turn the multi-pole switch to “Off ” for a few minutes

and then turn it back to “On”.

The hob will not switch off:

- disconnect the hob immediately from the power

supply.

AFTER SALES SERVICE

Before you call the After Sales Service

• Make sure that you cannot solve the problem yourself

following the points described in chapter

“Troubleshooting Guide”.

If after the above checks the fault still occurs, get in touch

with the nearest After Sales Service.

Please give:

• a short description of the fault;

• the exact type and model of hob;

• service number (i.e., the number that follows the word

SERVICE on the rating plate under the hob itself);

•your full address;

• your telephone number.

If any repairs are required, please contact an authorised After

Sales Service (to guarantee that original spare parts will be

used and repairs carried out correctly).

Failure to comply with these instructions may compromise

the safety and quality of the product.

INSTALLATION

Recommendations

Important: Disconnect the hob from the mains before

carrying out any installation work or servicing.

• All electrical connections must be made before

connecting the appliance to the power supply.

• Installation must be carried out by a qualified technician

in accordance with the manufacturer’s instructions and

in compliance with local regulations.

• Unpack the hob and make sure that the appliance has

not been damaged during transport. If you are not sure

contact the dealer or the nearest service centre.

Preparing the housing unit

• Cut the worktop to fit before installing the appliance.

Carefully remove any shavings or sawdust that could

prevent the appliance from running properly.

Attention: to install the hob on other surfaces than wood

(marble, plastic, ceramic, marble, stone, etc.) remember to

ask After Sales Service for the fixing plates (fig. 2)

Code 4819 404 78697.

• The hob must be fitted in a worktop with a minimum

thickness of 20 mm and a maximum of 50 mm.

• Insert a separator panel at a minimum distance of

20 mm from the bottom of the hob, so that it cannot be

accessed by the user.

• If there is an oven under the hob, make sure that it is

manufactured by us and equipped with a cooling

system.

• There must be nothing between the hob and the oven

(e.g. cables, insulating material, etc.).

• An adjacent column unit must be installed at least

100 mm from the edge of the hob.

• Cut an opening in the worktop of the given dimensions.

• We recommend you seal the internal edges of the

worktop with wood glue or silicone.

• If not already in place, apply the supplied seal to the

hob, after cleaning the adhesive surface thoroughly.

Glass-ceramic hob

Important: remove any protective film before installing the

hob.

Make sure that that the opening in the worktop for the hob is

cut according to the dimensions given in the drawing, paying

attention to the tolerance range.

The hob should not be forced into the worktop. Forcing the

glass-ceramic top may cause it to crack (even at a later date)!

• If the worktop is made of wood, use the spring clips and

screws provided.

1. Secure the spring clips (A) (fig. 1) with the screws

provided (B) (fig. 1) as shown, paying attention to the

specified distances.

2. Fit the hob into the worktop.

• If the worktop is made of marble, plastic, ceramic,

stone, etc., the hob must be secured with special

brackets (C) (fig. 2).

1. Fit the hob into the worktop (fig. 1).

2. Place the 4 brackets (C) in position in accordance with the

thickness of the worktop as shown in fig. 2.

3. Fasten the 4 screws (D) in the positions (E) (fig. 2).

Connecting the hob to the power supply

The installer is responsible for connecting appliances correctly

to the mains and for observing the safety regulations.

Note: the yellow/green earth wire must be connected to the

screw with the symbol .

• Strip approx. 70 mm of the cable sheath from the

power supply cable (G).

• Strip approx. 10 mm of sheath from the conductors.

Insert the cable (G) through the opening in the lid (F).

• Insert the cable into the cable clamp and connect the

conductors to the terminal block as indicated in the

diagram printed on the lid.

• Secure the power cable

(G)

by means of the cable clamp.

• Refit the protection lid (F).

• After the electrical connection, fit the hob from the top

and hook it to the fixing springs, according to the

illustration.

Declaration of conformity

• This cooktop has been designed, constructed and

marketed in compliance with:

- safety objectives of the “Low Voltage” Directive

2006/95/CE (which replaces 73/23/CEE and

subsequent amendments).

- the protection requirements of Directive “EMC”

2004/108/CE.

• This cooktop is suitable for contact with foodstuffs and

complies with EEC (CE) Regulation n. 1935/2004.

PROTECTING THE ENVIRONMENT

Disposal of packaging materials

• The packing material can all be fully recycled, as

confirmed by the recycling symbol .

• The various parts of the packing must not be sent for

waste, but recycled in conformity with the regulations

imposed by local authorities.

Disposal of used household appliances

• This appliance is marked according to the European

directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by

inappropriate waste handling of this product.

The symbol on the product, or on the documents

accompanying the product, indicates that this appliance

may not be treated as household waste. Instead it shall

be handed over to the applicable collection point for the

recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local

environmental regulations for waste disposal. For more

detailed information about treatment, recovery and

recycling of this product, please contact your local city

office, your household waste disposal service or the

shop where you purchased the product.

Energy saving

• Use pots and pans whose bottom diameter is equal to

that of the cooker plates, or slightly larger.

• Only use flat-bottomed pots and pans.

• If possible, keep the pot covered when cooking.

• Cook vegetables, potatoes, etc. with little water in

order to cut down cooking time.

• A pressure cooker allows you to save even more energy

and time.

Fig. 1

Fig. 2

Fig. 3

Whirlpool AKM 9010 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Andere handleiding(en) van Whirlpool AKM 9010

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info