328045
5
Verklein
Vergroot
Pagina terug
1/18
Pagina verder
5
ƽ DANGER
Do not use an open flame to check
for gas leaks. Be sure there are no
sparks or open flames in the area
while you check for leaks. Sparks
or flames will result in a fire or
explosion, which can cause serious
bodily injury or death, and damage
to property.
1).
1
(a)
(a)
(a)
A.
B.
ANNUAL MAINTENANCE
Inspection and cleaning of the Spider/Insect screen
To inspect the spider/insect screen, remove the
control panel. If there is dust or dirt on the screen,
remove the burner for cleaning the screen. Brush
the spider/inspect screen, lightly, with a soft bristle
brush (i.e. an old toothbrush).
ƽ CAUTION: Do not clean the spider/insect
screen with hard or sharp tools. Do not
dislodge the spider/insect screen or enlarge
the screen openings.
Lightly tap the burner to get debris and dirt out of
the burner tube. Once the spider/insect screen and
burner is clean replace the burner. If the spider/
insect screen becomes damaged or cannot be
cleaned, call Weber-Stephen Products Customer
Service for replacement parts.
Main Burner Flame Pattern
The Weber
®
gas grill burner has been factory set
for the correct air and gas mixture. The correct
flame pattern is shown.
1) Burner tube
2) Tips occasionally flicker
yellow
3) Light blue
4) Dark blue
If the flames do not appear to be uniform
throughout the burner tube, follow the burner
cleaning procedures.
Replacing Burner Tube
1) Your Weber
®
gas grill must be OFF and cool.
2) Unscrew and remove propane cylinder from the
valve/regulator assembly.
3) Open the lid.
4) Remove cooking grate.
5) Unscrew and remove the 1/4 x 20 inch stainless
steel hex nut and stainless steel washer that
holds the burner tube inside the cook box(a).
6) Carefully slide the burner tube out from the
cook box.
ƽ Caution: The burner openings(1) must
be positioned properly over the valve
orifices(2).
7) To reinstall the burner, reverse 5) through 7).
Make sure the igniter port hole(A) lines up with the
arrow tab(B) on the igniter box.
Ignition System Operations
If the ignition system fails to ignite the burner, light
the burner with a match. If the burner lights with a
match, then check the ignition system.
Check that both the white(1) and black(2) ignition
wires are attached properly.
Check that the ignition button pushes the igniter
(button) down, and returns to the up position.
If the ignition system still fails to light, Contact the
Customer Service Representative in your area
using the contact information on our web site. Log
onto www.weber.com
®
.
Main Burner Cleaning Procedure
Turn off the gas supply. Remove the burner.
(See Replacing Burner Tube.)
Look inside the burner with a flashlight.
Clean the inside of the burner with a wire (a
straightened-out coat hanger will work).
Check and clean the air shutter opening at the
ends of the burner. Check and clean the valve
orifice at the base of the valve. Use a Steel bristle
brush to clean outside of burner. This is to make
sure all the burner ports are fully open.
ƽ CAUTION: Do not enlarge the burner ports
when cleaning.
(2)
(3)
(4)
(1)
2
(2)
(1)
1.
2.
Check for gas leaks
After a period of nonuse, we recommend that you
perform the following maintenance procedures for
your safety.
Inspect the burner for correct flame pattern.
Clean if necessary, following the procedures
outlined in the “General Maintenance” section of
this manual.
• Check all gas fittings for leaks.
ƽ WARNING: You should check for gas leaks
every time you disconnect and reconnect a
gas fitting. Note: All factory-made connections
have been thoroughly checked for gas leaks.
The burners have been flame tested. As a
safety precaution however, you should recheck
all fittings for leaks before using your Weber
®
gas grill. Shipping and handling may have
loosened or damaged a gas fitting.
ƽ WARNING: Perform these leak checks even
if your grill was dealer- or store-assembled.
You will need a soap and water solution and a rag
or brush to apply it. To perform leak checks make
sure the Burner is in the off position and turn on
gas supply.
ƽ WARNING: Do not ignite burner while leak
checking.
Check for leaks by wetting the connections with
the soap and water solution and watching for
bubbles. If bubbles form, or if a bubble grows,
there is a leak. Note: Since some leak test
solutions, including soap and water, may be
slightly corrosive, all connections should be rinsed
with water after checking for leaks.
Check:
1) Regulator to propane cylinder connection.
ƽ WARNING: If there is a leak at connection
(1), remove propane cylinder. Do not operate
grill. Use a different propane cylinder and
recheck for leaks with soap and water
solution. If a leak persists after retightening
the propane cylinder, turn OFF the gas.
DO NOT OPERATE THE GRILL. Contact the
Customer Service Representative in your
area using the contact information on our
web site. Log onto www.weber.com
®
.
Check:
2) Valve to-regulator connections.
ƽ WARNING: If there is a leak at connection
(2) turn OFF the gas. DO NOT OPERATE
THE GRILL. Contact the Customer Service
Representative in your area using the
contact information on our web site. Log
onto www.weber.com
®
.
When leak checks are complete, turn gas supply
OFF at the source and rinse connections
with water.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Weber baby q bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Weber baby q in de taal/talen: Engels, Frans, Spaans als bijlage per email.

De handleiding is 3,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info