802124
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Webasto Charging the A/C system | 6
6244481A_ES_OI_II_Quebec-Montreal_R1234yf 5 / 8
1
2
3
5
4
Fig.4: Refrigerant bleeding
Vehicle interior Bleeding in case of refri-
gerant leakage
Vehicle floor Enclosure in case of off-
floor installation
Vehicle exterior
üAvoid making connections to the refrigerant circuit inside
the passenger compartment of the vehicle. In case the con-
nections are inside the vehicle, the joint must be segreg-
ated from the interior using seals and/or sealant and open
to vent outside the vehicle any eventual refrigerant leak.
üThe venting opening must be kept away from hot surfaces
and / or ignition sources.
üAvoid locating refrigerant connections e.g. hoses to fittings,
fittings to components (valves, filters, pressure switches,
safety valves, etc.) and charge ports in areas close to hot
surfaces (e.g. exhaust pipe, catalyst, engine block, etc…) or
elements likely to generate sparks or electric arcs.
üAvoid the installation of refrigerant solenoid valves inside
the vehicle.
uIn case not already installed: always install over-pressure
safety valves venting in area far from hot surfaces, power
electric lines and any other ignition source.
5.4 Installation
1
1
Fig.5: Mechanical installation
The unit comes prepared with 2 M6 rivet-nuts (1) on each side.
uSelect a suitable location for the unit.
uDesign brackets that firmly locate and hold the unit to the
vehicle interior.
The brackets should ensure stiffness and avoid vibrations
and potential cracks.
uMount the brackets on the unit with M6 bolts. Nominal
torque: 5Nm.
üMake sure you can work safely on the vehicle’s refrigera-
tion system.
uConnect the expansion valve to the vehicle’s refrigeration
circuit.
üFor a HVAC unit: Make sure you can work safely on the
vehicle’s cooling system.
uFor a HVAC unit: Connect the heater to the vehicle’s cooling
circuit.
5.5 Electrical connections
Fig.6: Electrical connections
1 + (red) 3 Compressor (yellow/green)
2 Gnd / - (black)
uMake the electrical connections according Fig. 6. See
„chapter9 for power and fuse requirements.
Avoid fitting relays, fuses and switches close to refrigerant
connections.
uInstall the control knobs/switches in a convenient location.
6 Charging the A/C
system
DANGER
Danger of fire
Carry out refrigerant charging operations in ventilated
areas, away from open flames, hot surfaces and any
other ignition sources.
Take into account these measures and all those aimed
at reducing the risk of ignition of the refrigerant in case
of a leakage.
Refer to SAE J 2845.
NOTE
Only use recovery/recycling/recharging equipment for
flammable refrigerants compliant to SAEJ2843.
uPerform a high pressure leak test with nitrogen. Accurately
solve any eventual leak to assure circuit tightness.
uPerform an evacuation test.
If present, activate the solenoid valves during the leak-test, va-
cuum and charge procedure to ensure the correct pressurization
of the entire system.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Webasto Montreal bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Webasto Montreal in de taal/talen: Engels als bijlage per email.

De handleiding is 1.09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Webasto Montreal

Webasto Montreal Gebruiksaanwijzing - Deutsch - 8 pagina's

Webasto Montreal Gebruiksaanwijzing - Français - 9 pagina's

Webasto Montreal Gebruiksaanwijzing - Italiano - 8 pagina's

Webasto Montreal Gebruiksaanwijzing - Espanõl - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info