805504
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
MILUX RF
General safety information
The instructions described in this manual must be observed. Failure to comply with
theses instructions will result in material damages, injury or fatal accidents.
This product must be used exclusively to regulate heating installations.
Other use is not compliant
Contents
1. Product characteristics
2. Display
3. Keypad
4. First use
5. RF Configuration
6. Standby switch
7. Operating modes
7.1. TIME SETTING menu
7.2. COMFORT Mode
7.3. REDUCED Mode
7.4. AUTOMATIC Mode
7.5. PROGRAM Menu
7.6. ANTIFREEZE Mode
8. Special functions
8.1. HOLIDAY function
8.2. Keypad lock
8.3. Cooling function
8.4. RESET function
9. Battery replacement
10. ITCS function (optional)
11. Technical characteristics
12. Problems and solutions
13. Recycling
14. Annexes
1. Product characteristics
Wireless communication by radio signal with the receiver connected to
the installation.
Weekly programmation by 1 hour step
9 built-in programs
4 user programs
Program graphic display
Room temperature and time display.
Comfort / Reduced / Anti-freeze temperatures.
Temporary temperature override
Automatic or Manual operation
Holiday function
Keypad lock function (child safety)
Battery operated > 2 years
Low battery pictogram
Battery replacement without loss of the program memory except the
hour
« O / I » switch for standby mode
Intelligent Temperature Control System function (optional): ITCS
2. Display
[1] : Operating mode menu
[2] : Temporary temperature override
[3] : Heating indicator
[4] : Room temperature or set temperature
[5] : Cooling indicator
[6] : if displayed, [4] indicates the ambient temperature
[7] : Holiday function activated
[8] : Current day graphic program
[9] : Hour
[10] : Day of the week (only available on weekly version)
[11] : Low batteries
3. Keypad
Validation key (OK)
Plus key (+)
Minus key (-)
Left navigation key ( )
Right navigation key (►)
4. First use
Check that the battery protection is well removed.
Put the switch on « I » position (see chapter 6- stanby switch))
Adjust the date and the hour (see chapter 7.1 TIME SETTING menu)
Do the thermostat RF configuration with the receiver (See chapter 5. RF
configuration)
The thermostat is ready for operation. The default operating mode is the
automatic mode with the factory program P1”,(see the detailed program
P1 in the annexes).
You can customize your program as you want. To do so, refer to chapter 7.5
PROGRAM Menu.
5. RF configuration
Put the receiver(s) to configurate in RF configuration mode (see
receiver’s leaflet).
On the thermostat, select the Automatic mode . Press 5 seconds
on (OK) key. If you are in RF configuration mode, the message «
» must appear. The thermostat sends its
configuration adress by radio signal .
Check on the receiver that the configuration is well done (see
receiver’s leaflet).
Verify the radio operating distance. Put the thermostat in the wanted
room to regulate the temperature. Let it in RF configuration mode :
is displayed. Close the doors and come back to
the receiver. Check the green LED on the receiver:
o If the LED blinks regularly several times per second, your
installation is functional.
o If the LED blinks irregularly and only one time, you are at
the range limit.
o If the LED doesn’t blink, you are out of range limit. Bring
imperatively your thermostat closer to the receiver.
Press (OK) key on your thermostat to exit the RF configuration mode.
Now, you thermostat operates with the receiver.
6. Standby switch
This switch is located under the product as shown below :
To put the product in standby, put the switch on « O » position. The screen
switches off to reduce battery consumption. The keys (+), (-), (◄) and (►) become
inactive. A press on (OK) key allows displaying briefly the ambient temperature
and the hour, together with the pictogram:
To activate the product, put the switch on « I » position. During 3 seconds, the
software version will be displayed. Then, the thermostat comes back in the
selected operating mode before the standby.
WARNING: In this standby mode, your installation can freeze.
7. Operating modes
Use the navigation keys (◄) or (►) to change the operating mode.
7.1. TIME SETTING menu :
Press (OK) to enter in the menu. The minute display is flashing.
Set minute value with (+) and (-) keys
Press (OK) key to validate.
Set hour value with (+) and (-) keys
Press (OK) key to validate.
( (►) key allows to return to the minute setting)
Weekly version
Set day value with (+) and (-) keys
(1=monday, 2=tuesday, …)
Press (OK) key to validate
7.2. COMFORT Mode :
In this mode, thermostat applies comfort setpoint temperature indefinitely. By
pressing (+) or (-) keys, setpoint temperature flashes and can be adjusted:
The ambient temperature is displayed after few seconds:
A press on (OK) key allows the displaying of comfort setpoint temperature.
To apply temporarily comfort mode, use the special function « HOLIDAY ».
7.3. REDUCED Mode :
In this mode, the thermostat applies reduced setpoint temperature indefinitely
By pressing (+) or (-) keys, setpoint temperature flashes and can be adjusted like
the COMFORT temperature. The ambient temperature is displayed after few
seconds. A press on (OK) keys allows the displaying of reduced setpoint
temperature.
To apply temporarily reduced mode, use the special function « HOLIDAY ».
7.4. AUTOMATIC Mode :
The thermostat follows the chosen program (see chapter 7.5 for the program
selection / edition) with respect to current hour.
By pressing (+) and (-), an overriden temperature can be adjusted until the next
program step:
The pictogram is displayed.
At the next program change, the pictogram will disappear and the program will
carry on.
7.5. PROGRAM Menu:
Press (+) or (-) keys to choose a program number:
= Comfort setpoint temperature set in the COMFORT mode
= Reduced setpoint temperature set in the REDUCED mode
If you select a built-in program « P1 to P9 », press (OK) key to apply this
program in the automatic mode .
A light weekly programs description is given below:
Number
Description
P1
Morning, Evening & Week-end
P2
Morning, Midi, Evening & Week-end
P3
Day & Week-end
P4
Evening & Week-end
P5
Morning, Evening (bathroom)
P6
Morning, Afternoon & Week-end
P7
7h - 19h (Office)
P8
8h - 19h, Saturday (Shop)
P9
Week-end (Secondary House)
A detailed programs description is given in annexes.
If you select a user program « U1 à U4 », press (OK) key to enter in edition
mode :
With navigation keys (◄) and (►), move the blinking cursor on the hour of the day
that you want to modify.
When the day seems to be correctly edited, press (OK) key.
Daily version: the day’s program is validated for every day of the week.
Weekly version: you switch to the next day edition. By validating the day 7, you
validate the program edition. This program will be followed by your thermostat in
automatic mode (see chapter 7.4).
7.6. ANTIFREEZE Mode :
In this mode, the thermostat applies antifreeze setpoint temperature indefinitely. By
pressing (+) or (-) keys, setpoint temperature flashes and can be adjusted like the
COMFORT temperature. The ambient temperature is displayed after few
seconds. A press on (OK) keys allows the displaying of the antifreeze setpoint
temperature.
To apply temporarily the antifreeze mode, use the special function « HOLIDAY ».
PPLIMW15279Aa
GB
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Watts Milux 2 RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Watts Milux 2 RF in de taal/talen: Engels als bijlage per email.

De handleiding is 0.76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info