805480
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
PPLIMW15250Ba
5 Parameter’s menu
Your thermostat has a parameter’s menu. To enter in this menu, press and maintain the
edition key ( ) during 5 sec. Then parameter menu will appear and first parameter
screen will be displayed
You can select a parameter which must be adjusted with navigation keys (◄) or (►).
Once the parameter is chosen, toggle the value with the (OK) key, modify it with (-) or
(+) and confirm your adjustment with (OK).
To leave the parameter menu, choose the parameter « End » and press (OK) or press
Return key ( ).
Default value & other possibilities
00 INI: Radio configuration
Radio configuration mode for wireless communication (refer to chapter 2.2)
01 dEG: Unit of the displayed temperatures
°C Celsius
°F Fahrenheit
04 Calibration of the internal probe
The calibration must be done after 1 day working with the same setting
temperature in accordance with the following description:
Put a thermometer in the room at 1.5M distance from the floor and check
the real temperature in the room after 1 hour.
When you enter on the calibration parameter “no” is displayed on the right
to indicate no calibration has made.
To enter the value shown on the thermometer, use the (-) or (+) keys to
enter the real value. Then, press (Ok) to confirm. The message “Yes
should be displayed; the value will be stored in the internal memory.
If you need to erase a calibration press on the escape key ( ).
The old value will be erased and the message no” will be displayed.
* Pay attention:
Only the heating element driven by the thermostat must be used during the
complete step of the calibration.
05 Calibration of the external wired probe
Same calibration method as described in parameter 04 above.
06 HG: Anti-freeze temperature
Default value 10°C.
Use the (-) or (+) keys to change the anti-freeze setting temperature. Then
press (Ok) to confirm.
08 Clr: Reset to Factory setting
Press and maintain (Ok) key during 10s to reset set point temperatures and
user parameters in this menu, to factory default settings.
* Pay attention:
Ensure you that you have all necessary elements to re-setup your
installation before to use this function.
09 Displayed only if the BT-DRF-02 is linked with a multizones receiver
CHA—
--: number of the linked zone
10 Software version
11 End: Exit the parameter’s menu
Press (OK) key to exit installation parameter menu and return to normal
operation.
6 Technical characteristics
Environmental:
Operating temperature:
Shipping and storage temperature:
0°C - 40°C
-10°C to +50°C
Electrical Protection
Installation Category
Pollution Degree
IP30
Class II
2
Temperature precision 0.1°C
Setting temperature range
Comfort, Reduced
Holiday (Antifreeze)
Timer
0,5°C step
5°C to 37°C
0,5°C to 10,0°C
5°C to 37°C
Regulation characteristics Proportional Band (PWM 2°C/10min)
or Hysteresis 0.5°C
Power Supply
Operating life 2 AAA LR03 1.5V Alkaline ~2 years
Sensing elements:
Internal & External (option)
Internal: NTC 10k
at 25°C
External: NTC 10k at 25°C (ß = 3950)
Radio Frequency 868 MHz, <10mW.
Software version Showed in parameter menu.
Vers xxx
Compatible receivers
BT-M6Z02 RF
BT-FR02RF
BT-WR02RF / BT-WR02HC
BT-PR02RF
BT-CT02
Other receivers can be compatible, check
on the instruction manual of your receiver
CE Directives
Your product has been designed in
conformity with the European Directives.
R&TTE 1999/5/EC
EMC 004/108/EC
RoHS 2011/65/EU
Product conformed to :
Classification :
Contribution :
UE 811/2013 and 2010/30/UE
IV
(2%)
7 Troubleshooting & Solution
My BT DRF-02 doesn’t start
Batteries Problem
- Check if the protection sticker on the batteries is removed.
- Check the batteries orientation.
- Check the capacity of the batteries
My BT DRF-02 Led, blinks in Red
Problem on sensors
The logo blinks (ambient sensor)
- Contact your installer or seller.
The logo blinks (Floor sensor)
- Check the connection of the sensor.
- Disconnect the sensor, and check it with an ohmmeter (the
value must be around 10kohms)
Batteries level is too less
The logo blinks (Batteries)
- Replace the batteries.
Humidity measurement
problem (*) The logo blinks and the thermostat displays ‘Err »
- Contact your intaller
My BT DRF-02 seems work correctly but the heating or the cooling doesn’t
work correctly
Output
On the receiver:
- Check the good reception of RF signal (
refer to
chapter
2.2.1)
- Check the connections.
- Check the power supply of the heating element.
- Contact your installer.
RF
communication
Check the following points :
- The receiver must be put at a minimum distance of 50cm
of all others electrical or wireless materials (GSM, Wi-Fi..)
- The receiver shouldn’t be fixed on a metallic part or too
close of hydraulic pipes… (Copper…)
Sensor calibration
- Try to calibrate your thermostat (
refer to
user menu
parameter 04)
- Contact your installer, to check & adjust the regulation
parameters with your heating system.
Configuration
The logo blinks :
- Cooling request is made by the central (BTCT02) but
the thermostat doesn’t allow (refer to parameter 21
chapter 8).
Humidity protection
(*)
The logo blinks:
- humidity regulation is activated (refer to parameter 34
chapter 8)
- condensation is detected (refer to parameter 35 chapter 8)
8 Advanced installer’s parameters menu
In order to enter in the menu, press on the escape key
during 5 seconds
The following display with the first parameter appears:
- Once you entered in the menu, go to the parameter which you want change by using
the keys (◄) or (►).
- Use the keys (+) or (-) to edit and modify and confirm by pushing the (OK) key.
- To leave the parameter menu, go to the parameter “End” and press the (OK) key
.
Parameters Installer’s Advanced Menu
nam
es
Description of the
parameter
Factory
value Other possibility
20 REG Selection of the sensor used
for the regulation.
“AIR”
Internal
ambient
sensor
“amb”
External ambient
sensor
Following options
aren’t available with all
receivers:
“FLR”
Floor sensor
regulation
“FL.L”
Air regulation with
floor limitation
possibilities
(refer to parameters
25&26)
21 MOd Working mode selection of
the thermostat
“Hot”
Heating
mode
“Cld”
Cooling mode
“rEv”
reversible menu
activation
“Aut”
Automatic mode
21
(**) Cld
Use this option if you want
to allow the zone to work in
cooling mode
“yes”
Function
activated
“no”
Function deactivated
22
View of the measured
values of the internal
sensor.
“__._” °C/°F
23
View of the measured
values of the external
(Ambient) sensor.
“__._”°C/°F
24
View of the measured
values of the floor sensor
connected to the receiver.
“__._”°C/°F
25 FL.L Lower limit of the floor
temperature.
“no”
The lower
limitation is
not used
From 5°C to
“FL.Hi”
26 FL.H Upper limit of the floor
temperature.
“no”
The upper
limitation is
not used
From “FL.Lo” to 40°C
27 tYP Selection of regulation type.
“bp”
Proportional
band
(PWM)
“hys”
Hysteresis (On/Off)
28 UF1 Concrete choice.
“uf1”
For liquid
concrete
with low
thickness
< 6cm
“uf2”
For traditional
concrete with
thickness
> 6cm
29 Bp1 Floor covering choice. “Bp1”
For tiling
“Bp2”
For wood parquet
(floating or not)
30 Uir
Pilot wire function for
French Market application
Use this option if your
installation has the pilot wire
installed in combination with
an energy saver.
“yes”
Function
activated
“no”
Function deactivated
31 min Minimal value of the setting
range. 5.0°C From 5°C to 15.0°C
32 MAX Maximal value of the setting
range. 37.0°C From 20°C to 37.0°C
33 Uin
Automatic open window
detection.
(refer to chapter 4.2)
“yes”
Function
activated
“no”
Function deactivated
34(*) rH Percentage value of the
humidity setting 55% From 0% (“no”) to
100%
35(*) dEv
Anti-condensation function
(when condensation is
detected, cooling system is
stopped or/and dehumidifier is
activated)
“yes”
Function
activated
“no”
Deactivated function
36 EEp
All parameters will be
reloaded with the factory
values
Press on the (OK) key during few
seconds.
37 End To exit the installer’s menu Press on the (OK) to exit.
(*):concerns version with humidity sensor
(**):concerns thermostat if it is linked with a central (BT-CT02) or with a BT-M6Z02 RF
http://www.wattselectronics.com
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Watts BT-DRF-02 - BELUX LIGHT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Watts BT-DRF-02 - BELUX LIGHT in de taal/talen: Engels als bijlage per email.

De handleiding is 0.5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info