583708
2
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
128-8602
2 of 8
This Keyless Entry System is designed to provide a convenient electronic means to gain access to the vehicle by
providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the
vehicle's dome lights, as well as exterior parking lights. Although not an alarm system, this unit also incudes a starter
interrupt circuit output. It also includes two additional auxiliary outputs designed to allow for control over optional devices
such as a power trunk release or engine starting device.
BEFORE BEGINNING THE INSTALLATION:
1) Find locations to mount the following items:
Control Module
Dash Mounted LED
Valet/Program/Manual Override Switch
2) Determine the type of factory power door lock system in use. Knowing the type of system before beginning
the installation can make the installation easier and faster since you can build whatever interface (if needed)
beforehand.
3) Determine whether the vehicle includes a power trunk release system and if so what type it is.
INSTALLATION OF COMPONENTS:
CONTROL MODULE:
The Control Module is NOT waterproof, DO NOT mount it in the Engine Compartment. Select a mounting location under
the dashboard. Choose a mounting location that will not interfere with proper operation of the vehicle's steering column
mechanism and brake and gas pedals. Secure the Control Module in the chosen location. Wait until all components
have been installed and all connections made before plugging in the main connectors.
DASH MOUNTED LED:
The small Red LED included in the kit serves as a visual indicator of the system's status and provides a visual deterrent
to a potential thief. The LED also provides important feed back information during the transmitter and feature program
modes. The LED should be installed in the dashboard in a highly visible area that may be seen from the driver’s seat as
well as from outside the vehicle. Try to choose a location close enough to the Control Module so that the LED's wires will
reach. Carefully inspect the area behind your chosen location to insure that the drill will not penetrate any existing factory
wiring or fluid lines. Drill a 1/4" hole and pass the connector end of the LED through the hole and route the wires toward
the location of the Control Module. Press the LED firmly into place until it is fully seated.
VALET / MANUAL OVERRIDE SWITCH :
Since much of the use of this switch by the vehicle operator requires concurrent operation of the ignition key switch, it is
recommended that the Valet / Manual Override Switch be placed such that it can be reached by the driver's left hand, while
they operate the ignition key switch with their right hand. The switch can be mounted to the lower dash panel in the drivers
area. Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch and also
that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and mount the
switch by passing it through the panel from the opposite side. Secure the switch using the nut, star washer, and on/off
face plate. It is suggested that the switch be oriented to allow the on position to be up toward the driver and the off position
to be down or away from the driver. Route the switch’s wires and connector toward the location of the Control Module.
RED Wire (Connects to RED/WHITE wire at harness plug): Main 12 Volt Input Wire
These are the main power input wires for the system. Both wires connect to a separate fuse holder contained in the
harness. These fuse holders each hold a separate ATC fuse, one 5AMP and one 10AMP. This RED wire must be
connected to a constant power wire at the vehicle's ignition switch harness or fusebox.
Locate a constant power wire at the vehicle's ignition switch harness. This wire will read +12VDC at all times, regardless
of the position of the ignition key switch. Attach the RED wire of the harness to this point by splicing and taping the
connection.
YELLOW Wire: Ignition Input Wire
This wire provides the system with an ignition power input from the vehicle. Connect this wire to the Ignition wire (primary
ignition wire) from the ignition switch. This vehicle wire will show +12VDC when the ignition key is turned to the "ON" or
"RUN" position
and when turned to the "START" or CRANK" positions and will have 0VDC when the key is turned to the
"OFF" and "ACCESSORY" positions.
Locate an ignition power wire at the vehicle's ignition switch harness. By splicing and taping the connection, attach the
YELLOW wire of the system to this point.
WHITE Wire: Positive Parking Light Flash Wire
This wire is designed to output a +12VDC positive light flash output, driven by the UNITS's internal relay, to be connected
2
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voxx APS-45N Prestige bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voxx APS-45N Prestige in de taal/talen: Engels als bijlage per email.

De handleiding is 0,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info