766094
4
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
16 17
1. Safety regulations
1.1 General information
These safety regulations contain fundamental information, which must be observed during installation, operation and
maintenance. All persons working on and with the clipper must read the operating instructions. The operating instruc-
tions must bepermanently available at the machine usage site.
1.2 Fundamental safety instructions
Observe the legal regulations on regular examinations.
Also observe the industrial safety regulations.
1.2.1 Power supply
Only insert the plug into correctly installed sockets. Defective electrical installations can cause an electric shock or a
short-circuit. Sockets should be equipped with an earth leakage circuit breaker (FI). Observe your local pertinent regu-
lations. Only carry out maintenance and cleaning tasks after pulling the plug. Never leave the machine unsupervised
when plugged in. Clipping animals is only permissible, if children are kept away from the clipping location. Do not store
your machine in reach of children!
1.2.2 Maintenance and service obligation
Never use a damaged machine for clipping. Only allow authorised technical personnel to repair the housing or defective
electrical cable.
1.2.3 Radiation
The clipper examination complies with the fundamental protection requirements according to the harmonised European
standards of the EEC Directive. EU Directive: 83/336/EEC of 03/05/1989
1.2.4 Remaining risks
Please notify us of operational dangers and risks, which do not occur when directly trimming the animals.
This also applies to endangering technical defects.
1.3 User requirements
Observe and comply with the instructions in this manual to ensure safe use of the clipper.
The user has read and understood the operating instructions or an expert has explained the operation and
pointed out the risks.
The user is experienced in clipping animals. Children and frail persons (without supervision) should not use the clipper.
2. Designated use
2.1 Intended purpose
The clipper is exclusively intended for clipping cattle, horses or large dogs. Any other use, in particular on humans, is
explicitly prohibited.
2.2 Technical data
Type designation: 18192
Supply voltage: 220 – 240 V AC
Motor rating: 200 W
Frequency: 50 Hz
Dimensions (W/H/L): 80 x 62 x 295 mm
Weight without cable: 1190 g
Sound pressure level: 85 dB (A)
Strokes: 3000/ min
Protection class: II
Operating conditions
Max. ambient temperature: 0 – 40° C
Max. air humidity: 10 – 90 % (relative)
2.3 Equipment
1 clipper with clipper head, 1 set of shear blades (mounted), (100 ml), 1 screwdriver, 1 operating manual and
1 storage case
3. Initial commissioning
3.1 Inspection and operating instructions
The inappropriate use of electrical devices, in particular animal breeding devices, is dangerous! Therefore, observe the
following, accident prevention measures before starting the machine: • Never switch the machine on without properly
mounted clipping plates • The volt specification on the rating plate must correspond to the mains voltage. The machine
may only be operated with AC • Avoid any contact with the moving blades • Always pull the power supply plug out
prior to maintenance work! Do not touch the blade area, even if the machine is switched off, as long as the machine is
connected to the current supply • Always place machine on a dry surface and store in dry rooms • Avoid any contact
with a machine, which is in contact with liquids. Never clip wet animals. Liquids that have penetrated into the machine
reduce the electrical insulation. There is the imminent danger of an electric shock or short-circuit. Only clean the
machine with a dry cloth and a paint-brush or brush • A cable lying on the floor can get caught and be dangerous. Lay
the cable carefully and safely before clipping. Prevent the clipper connection cable from kinking or tangling. Ensure that
animals do not stand on the cable, walk over it or get caught. Keep the cable away from hot surfaces. Never wind the
cable around the machine. This can result in insulation damage and cable break. Examine the cable regularly for de-
fects • Set the machine switch to off (fig. 3) before pulling the plug from the mains • Do not use damaged shear blades
with broken off teeth. Only use sharp shear blades. Only use the original shear blades. • Never insert an item into an
opening of the machine. The machine noise can disturb animals. A kick or the weight of the animal can result in sub-
stantial injuries. Therefore fixate the animal sufficiently. • Animals should only be clipped, when unauthorised persons
do not have access to the clipping location • Only clip in well-ventilated rooms and never in the proximity of explosive
materials. These safety notes must be observed in all cases!
3.2 Blade adjustment with the tension screw
Adjust as follows when placing into operation:
Prior to clipping: Turn the tension screw up to the first noticeable resistance with the machine switched off. Then con-
tinue to turn the tension screw by a further 1/4 rotation.
18192=BA_FarmClipper4_148x210_0816.indd 17 25.08.2016 14:40:17
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voss Proficut bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voss Proficut in de taal/talen: Engels als bijlage per email.

De handleiding is 1,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Voss Proficut

Voss Proficut Gebruiksaanwijzing - Nederlands - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info