738216
56
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
56
10. Additional functions
Youcanusethefunctionbuttons(CandI)toenablearangeofdifferentfunctions.Themultimeterbeepseachtime
you press a button.
a) SELECT function
Some measuring modes have additional sub-modes. The sub-modes are marked in grey around the control dial.
Pressthe“SELECT”button(I)briey(<2s)toselectasub-mode..Pressthe“SELECT”buttonagaintoswitchtothe
next sub-mode.
b) REL function
The REL function allows you to take a reference measurement to avoid possible line losses (e.g. during resistance
measurements). This function resets the current measurement to zero.
Toenablethisfunction,pressandholdtoe“REL”buttonforapproximatelyonesecond.“Δ”willappearonthedisplay
and the measurement will be reset to zero. The automatic range selection function will be disabled.
To disable this function, change the measurement mode or press and hold the “REL” button for approximately one
second.
The REL function is not available in the following modes: Battery test, diode test and continuity
test. The “REL” button only works when a measured value is displayed. It cannot be used when
“OL” is displayed.
c) HOLD function
This feature freezes the current reading on the display so that you can record it for future reference.
When testing live wires, make sure that this function is disabled before taking any measurements,
otherwise the measurement will be incorrect!
Press the “HOLD” (C) button to enable this feature. The multimeter will beep and “H” will be displayed. To disable the
hold feature, press the “HOLD” button or change the measuring mode.
d) Auto power-off function
The multimeter switches off automatically after 15 minutes if no buttons are pressed. This function saves battery
power and prolongs the battery life. The symbol will be displayed when the automatic power-off feature is enabled.
The multimeter will beep several times approximately 1 minute before it turns off. If the “REL/HOLD” or “SELECT” but-
ton is pressed before the multimeter switches off, the multimeter will beep again in 15 minutes. A long beep indicates
that the multimeter is switching off.
To switch the DMM back on, move the control dial over the “OFF” position or press the “REL/HOLD” or “SELECT”
button.
The automatic power-off feature can be disabled.
Follow the steps below to disable the automatic power-off feature:
Switch the multimeter off (move the control dial to the “OFF” position). Hold down the “SELECT” button and switch
on the DMM using the control dial. The multimeter will switch on and the “ ” symbol will no longer be visible on the
display. The automatic power-off feature will remain disabled until the multimeter is turned off using the control dial.
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voltcraft VC271 TRMS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voltcraft VC271 TRMS in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 5,74 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info