738223
46
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
46
e) Diode test
Make sure that all the circuit parts, switches and components and other objects of measurement are
disconnected from the voltage and discharged.
Turn the digital multimeter on and select the measuring setting position
” with the rotary switch (5). “M” and the “ ” unit symbol are
displayed in the LC display (4).
Resistance measuring in auto-mode is selected by default and cannot
be switched off. The symbol and M for mega indicate resistance
measuring mode appear in the LC display (4). To select the diode
testing mode, press the SELECT button (1) three time until the diode
symbol “ ” appears in the LC display (4).
Insert the red measuring lead into the V socket (8) and the black
measuring lead into the COM socket (9).
Now connect the two measuring prods to the object to be measured
(diode, transistor, etc.). The red measuring tip indicates the positive
pole, the black measuring tip the negative pole.
Connect the test leads with the prods to each end of the diode. Record
the measurement displayed. Reverse the test leads and record the
measurement displayed as well.
Press the HOLD button (12) in order to lock a measured value if
needed. The hold symbol appears in the LC-display (4). Press the
HOLD button (12) in order to release the locked value. The hold symbol
disappears from the LC-display (4).
D
If the LC display (4) shows a voltage in volt (V), the diode shows a forward bias. A voltage drop of 0.5 - 0.8 may
be observed on the pn-junction of a good silicone diode. If “OL” (in the centre of the LC display (4)) is shown, the
diode measured is reverse biased, or the diode is faulty (interruption).
Perform a counter-pole measuring for verication. The red measuring lead corresponds to the positive pole
(anode), the black measuring lead to the negative pole (cathode).
A silicone diode has an on-state voltage drop of approx. 0.5 – 0.8 V, germanium diodes typically have about
0.2 - 0.3 V.
A diode is shortened if readings show the same voltage drop in both directions (approximately 0.4 V).
A diode is bad (opened) when not allowing current to ow in either direction. The digital multimeter shows “OL” in
both directions in such case.
After measuring, remove the measuring leads from the measuring object and turn the digital multimeter off. Turn
the rotary switch (5) to the position “OFF”.
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Voltcraft VC185 TRMS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Voltcraft VC185 TRMS in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 10,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info