652087
7
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
7
nun bereit, eine DCC-Adresse zu empfangen
und als eigene zu speichern.
4. Per Digitalzentrale die gewünschte DCC-Digi-
taladresse durch Druck auf die entsprechende
Taste / Schaltäche senden.
Der Decoder empfängt den Befehl, registriert
die Adresse und quittiert dies durch Bewegung
der Weiche an Ausgangsgruppe 1.
Damit ist der Decoder unter der neuen Adresse
betriebsbereit. Falls Sie die Adresse künftig än-
dern möchten, wiederholen Sie die Prozedur ein-
fach.
MM-Digitaladresse zuweisen:
1. Decoders gemäß Abb. 2 anschließen (inkl. eine
Weiche an Ausgangsgruppe 1).
2. Digitalsystem einschalten.
3. Roten Taster am Decoder einmal drücken.
Die an Ausgang 1 angeschlossene Weiche
schaltet langsam hin und her.
4. Roten Taster am Decoder
ein zweites Mal drücken.
Die an Ausgang 1 angeschlossene Weiche
schaltet schnell hin und her. Der Decoder ist
nun bereit, eine MM-Adresse zu empfangen
und als eigene zu speichern.
5. Per Digitalzentrale die gewünschte MM-Digital-
adresse durch Druck auf die entsprechende Ta-
ste / Schaltäche senden. Der Decoder emp-
fängt den Befehl, registriert die Adresse und
quittiert dies durch Bewegung der Weiche an
Ausgangsgruppe 1.
Damit ist der Decoder unter der neuen Adresse
betriebsbereit. Falls Sie die Adresse künftig än-
dern möchten, wiederholen Sie die Prozedur ein-
fach.
Adress-Einstellungsmodus verlassen
ohne Änderung:
Mit einem dritten Druck auf den roten Taster des
Decoders verlassen Sie ohne Veränderung der
Adresse den Adress-Programmiermodus.
Hinweis:
Der Decoder lässt sich nur auf eine Gruppe
von 4 aufeinanderfolgenden Weichenadressen
programmieren, z. B. 1 - 4, 5 - 8, 9 - 12. Es ist
also nicht möglich, den Decoder auf die Adres-
sen 3 - 6 zu programmieren, da diese Adres-
sen zwei verschiedenen Gruppen angehö-
ren. Welche Taste innerhalb der Vierergruppe
Sie bei der Programmierung drücken, ist völlig
gleich. Alternativ können Sie auch einen Wei-
chenschaltbefehl über ein Modellbahn-Steue-
rungsprogramm Ihres Computers (WIN-DIGI-
PET) auslösen.
ready to receive a DCC address and to store it.
4. Transmit the desired digital address by push-
ing the corresponding buttons on the com-
mand station. The decoder receives the com-
mand, registers the address and conrms this
by switching the turnout wired to output 1.
Then the decoder is ready for operation with its
new address. Should you wish to change the ad-
dress at a later stage simply repeat this procedure
and enter the new address.
Assigning an MM digital address:
1. Wire the decoder according to Figure 2 (includ-
ing a turnout on output group 1).
2. Turn on the digital system.
3. Press the red button on the decoder once.
The turnout wired to output 1 will switch slowly
forwards and backwards.
4. Press the red button on the decoder
once more.
The turnout wired to output 1 switches quickly
forwards and backwards. The decoder is now
ready to receive an MM address and to store it.
5. Transmit the desired digital MM address by
pushing the corresponding buttons on the com-
mand station. The decoder receives the com-
mand, registers the address and conrms this
by switching the turnout wired to output 1.
6. Then the decoder is ready for operation with its
new address. Should you wish to change the
address at a later stage simply repeat this pro-
cedure and enter the new address.
Exiting the address setting mode
without programming or changing an
address:
With a third press of the red button you can exit
the address programming mode without having
programmed an address.
Note:
The decoder can only be programmed to a
group of four consecutive addresses e.g.: 1
– 4, 5 - 8, and 9 - 12. It is not possible to pro-
gram the decoder for instance to the addres-
ses 3 – 6 since these addresses belong to two
different groups of addresses. It is unimportant
which button you press within the group of four
for programming the address. Alternatively you
may also activate a switching command for a
turnout or signal with a train control software
running on your PC e.g.: WIN-DIGIPET.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Viessmann 52121 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Viessmann 52121 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info