756782
12
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
POWX07583 EN
Copyright © 2021 VARO P a g e | 12 www.varo.com
12.1 Cross-cut sawing mode
12.1.1 Settings
When the bevel lock (16) is loosened, you can tilt the machine head to the left by up to
45°.
The turntable (11) can be adjusted from -45° to +45° by undoing the turntable locking knob
(9).
Start the saw by pressing the trigger switch (20) and switch A (8). The switch A (8) must
remain pressed during the sawing work.
12.1.2 Mitre 90° and turntable 90° (Fig. 13)
Important! Place the work-piece for sawing firmly on the machine surface and secure it
with the clamp (25) to prevent it from moving during the sawing process.
When you have switched on the saw, wait until the saw blade (18) has reached maximum
speed.
Press switch A (8) and trigger switch (20), using the cutting handle (6), apply steady and
light downward pressure to move the machine head through the work-piece.
After the cutting process is finished, bring the machine head back to its upper (home)
position and release trigger switch (20).
Important. The integral resetting springs will automatically lift the machine head.
Do not simply let go of the handle (6) after cutting, but allow the machine head to rise
slowly, applying slight counter pressure as it does so.
12.1.3 Mitre 90° and turntable 90°- 45° (Fig. 14)
The crosscut and mitre saw with table can be used to make right and left angular cuts of 90°-
45° in relation to the saw guide (21).
Move the machine head to its upper position.
Release the turntable (11) by slackening the turntable locking knob (9).
Set the turntable (11) to the desired angle, i.e. the marking on the turntable must coincide
with the desired angular setting on the base plate (1).
Retighten the turntable locking knob (9) to secure the turntable (11) in place.
12.1.4 Mitre cut 90°- 45° and turntable 90° (Fig. 15)
The crosscut and mitre saw with table can be used to make mitre cuts of 90° - 45° in relation
to the work face.
Move the machine head to its upper position.
Fasten the turntable (11) in 90° position.
Undo the bevel lock (16) and use the cutting handle (6) to tilt the machine head to the left
until the pointer coincides with the required angle value.
Retighten the bevel lock (16) and make the cut.
12.1.5 Mitre cut 90°- 45° and turntable 90°- 45° (Fig. 16)
The crosscut and mitre saw with table can be used to make mitre cuts to the left of 90°- 45° in
relation to the work face and, at the same time, 90° - 45° in relation to the saw guide (21)
(double mitre cut).
Move the machine head to its upper position.
Release the turntable (11) by slackening the turntable locking knob (9).
Adjust the turntable (11) to the angle required
Retighten the turntable locking knob (9) in order to secure the turntable in place.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Varo POWX07583 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Varo POWX07583 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Varo POWX07583

Varo POWX07583 Gebruiksaanwijzing - Nederlands - 17 pagina's

Varo POWX07583 Gebruiksaanwijzing - Deutsch - 17 pagina's

Varo POWX07583 Gebruiksaanwijzing - Français - 17 pagina's

Varo POWX07583 Aanvulling / aanpassing - Alle talen - 14 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info