469483
12
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
12 Instructions for use ecoTEC / 838402_06
The status displays provide information on the operat-
ing status of the appliance.
Press the “i” button (1) to activate the status displays.
The display (2) then shows the current status code, for
example “S. 4” for burner operation. The table below
explains the most important status codes.
In switching phases, for example on starting up again
after the flame was extinguished, the status message
“S.” briefly appears.
Press the “i” button (1) again to switch the display
back to normal mode.
h
Note
The ecoTEC exclusive display has also cleartext
for a direct information
4.8 Troubleshooting
In the unlikely event that a problem occurs with the oper-
ation of the ecoTEC boiler, the following points should be
checked:
Boiler fails to operate:
Is the gas supply turned on (see 4.3.1)?
Is the water supply turned on (ecoTEC combination
boilers only, see 4.3.1)?
Is there enough water in the heating system (see 4.3.2)?
Is the electrical supply switched ON?
Is the main ON/OFF control in the “ON” position
(switch position “I”, see 4.4)?
Is there an ignition problem (see 4.8.2)?
Hot water operates but no central heating (ecoTEC
combination boilers only)
- Is the heating turned ON (see 4.6.1)?
- Are all external heating controls ON (see 4.6.3)?
a
Caution
Inappropriate modifications can cause damage.
If your boiler still does not operate then please
consult your installer or Vaillant Service Solu-
tions (0870 6060 777).
4.8.1 Problems due to low system water pressure
The device switches to “Fault” if the water pressure in
the heating system is too low. This malfunction is indi-
cated by the fault code “F.22” (dry fire) or “F.23” or
“F.24” (lack of water).
You can only start up the appliance again when the
heating system is sufficiently filled with water.
4.8.2 Ignition problems
If the burner fails to ignite after five attempts, the de-
vice does not start up and switches to “Fault”. This is in-
dicated by the fault code “F.28” or “F.29” in the display.
On ecoTEC plus appliances the display also shows the
flame symbol with a cross through it (1). On ecoTEC pro
appliances, the red LED (2) also lights up.
Automatic ignition can only take place after you manu-
ally reset the fault.
To reset the fault, press the reset button (3) and hold
it down for one second.
3
plus/exclusive pro
Fig. 4.17 Troubleshooting
a
Caution
If the boiler still shuts off after three attempts
of resetting, please consult your installer or
Vaillant Service Solutions.
4.8.3 Flue problems
The appliances are fitted with a fan. If the fan does not
work properly, the appliance will switch itself off.
The display shows the symbols
and and the fault
message “F.32”.
h
Note
If contacting Vaillant Service Solutions please
remember to quote the fault code, as this will
help to pinpoint the fault.
4.9 Turning off the boiler
1
Fig. 4.18 Switching off the appliance
Turn the main ON/OFF control (1) to the „0“ position.
4 Operation
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vaillant ecoTEC exclusiv 365 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vaillant ecoTEC exclusiv 365 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Vaillant ecoTEC exclusiv 365

Vaillant ecoTEC exclusiv 365 Bijvullen ketel - Nederlands - 2 pagina's

Vaillant ecoTEC exclusiv 365 Gebruiksaanwijzing - Nederlands - 28 pagina's

Vaillant ecoTEC exclusiv 365 Gebruiksaanwijzing - Deutsch - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info