602543
4
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
1 Safety
4 Installation instructions aroTHERM 0020147164_04
1.3.7 Risk of material damage caused by
using an unsuitable tool
Use the correct tool to tighten or loosen
screw connections.
1.3.8 Avoid environmental damage
caused by escaping coolant
The heat pump contains R410A coolant.
The coolant must not be allowed to escape
into the atmosphere. R410A is a fluorinated
greenhouse gas covered by the Kyoto Pro-
tocol, with a GWP of 1725 (GWP = Global
Warming Potential). If it escapes into the at-
mosphere, its impact is 1725 times stronger
than the natural greenhouse gas CO
2
.
Before the heat pump is disposed of, the
coolant it contains must be completely
drained into a suitable vessel so that it
can then be recycled or disposed of in
accordance with the regulations.
Ensure that only officially certified com-
petent persons with appropriate protective
equipment carry out maintenance work on
the coolant circuit or access it.
Arrange for the coolant contained in the
product to be recycled or disposed of by
accredited specialists in accordance with
regulations.
Only use coolant R410A.
Only use a suitable R410A tool for the
filling, pressure measurement, vacuum
generation and discharge.
Solder the lines using shielding gas. Check
the lines for leak-tightness using nitrogen.
In the event of a repair or maintenance
work, fill the coolant circuit with liquid
coolant.
If the coolant circuit is not leak-tight, check
which component must be repaired or re-
placed.
Lower the negative pressure in the coolant
circuit to max. 10 mbar (1000 Pa).
When filling the coolant circuit, observe the
values in the "Technical data" section.
1.4 Regulations (directives, laws,
standards)
As part of the installation, commissioning and
operation of the heat pump and the DHW
storage you must take into account the cur-
rent versions of the following regulations or
standards, along with any local directives or
guidelines that may apply.
Electricity at work act.
Health and safety at work act.
Relevant Utility supplier’s regulations.
Water regulations and by-laws.
Environment agency and local council re-
quirements regarding bore holes, water
courses, or noise levels.
Gas safety installation and use regulations
concerning any associated gas fired heat
source used within the heating system.
Building regulations part “L&P” and direct-
ives concerning energy saving.
Building regulations such as G3 covering
Hygiene and L8 Legieonella.
COSHH regulations.
Other relevant bodies such as HETAS and
OFTEC.
BS7671 requirements for electrical installa-
tions.
All other national and regional relevant regu-
lations for the installation of heat pumps and
heating systems must be followed.
1.5 CE label
The CE label shows that the products comply
with the basic requirements of the applicable
directives as stated on the identification plate.
The declaration of conformity can be viewed
at the manufacturer's site.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Vaillant aroTHERM VWL 155-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Vaillant aroTHERM VWL 155-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Vaillant aroTHERM VWL 155-2

Vaillant aroTHERM VWL 155-2 Gebruiksaanwijzing - Nederlands - 20 pagina's

Vaillant aroTHERM VWL 155-2 Gebruiksaanwijzing - Deutsch - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info