473890
5
Verklein
Vergroot
Pagina terug
1/59
Pagina verder
X3DW VDO CYCLECOMPUTING8
GB SLO PL JP
JP PL SLO GB
www.vdocyclecomputing.com X3DW 9
3.2 Timer-Functions
The X3DW has 7 different selectable timers.
Only the timer selected is shown on the display.
STOPWATCH
You can use the stopwatch to measure as ma-
ny times as you want. Maximum value: 23:59:59
HH:MM:SS. If the maximum value is exceeded,
the counter starts again at zero.
Start with
M
. Stop with
M
.
Reset with
C
for 3 seconds.
TIMER 1, TIMER 2, TIMER 1+2
A time can be entered for TIMER 1 and TIMER 2.
The timer counts up to the set time, jumps back to
zero and counts again up to the set time.
At the end of TIMER 1, 1 beep is heard, at the end
of TIMER 2, 2 beeps are heard. TIMER 1+2 combines
the two timers, e.g. for interval training.
The number of repeats for TIMER 1+2 can be entered
beforehand.Maximum value 23:59:59 HH:MM:SS,
99 repetitions. Start with
M
. Stop with
M
.
Reset with
C
for 3 seconds.
COUNTDOWN
On the countdown timer, a time can be set.
The timer counts down backwards from this time
to zero. At the end of the countdown a beep is
heard. Start with
M
. Stop with
M
.
Reset with
C
for 3 seconds.
TIME TRIAL
On the TIME TRIAL timer, a distance can be set
(time trial distance). Whilst cycling, the expected
ride time, based on the average speed and the
distance still to be cycled, is constantly shown
alternately on the display.
Start with
M
. Stop with
M
.
Reset with
C
for 3 seconds.
LAP TIMER
The lap timer can store 30 laps.
For every lap, the following is saved:
B
Time
B
Distance
B
Average speed
The next lap can be started either manually or
automatically. For the automatic start, a distance
NAVIGATOR/SELECT
SELECT shows that there is a submenu for the main
NAVIGATOR menu. You open the submenu with
M
.
B
Set
You can set a starting value here and decide whether
the counter counts forwards or backwards from
this starting value. Further details in Chapter 5.7.
B
Reset
In the reset submenu you set the NAVIGATOR
back to zero. You leave the submenu by pressing
C
again.
3.3 Cadence option
The cadence menu is only available if
B
the cadence transmitter is installed,
B
the transmitter was recognized during pairing.
After pairing the cadence transmitter, the current
cadence is shown in section 2 of the display.
In function mode it is possible to select the CADENCE/
MORE menu using the buttons.
Confirming with
M
opens the menu and gives you
access to the information.
Using you come to:
B
AVG CADENCE
B
MAX CADENCE
Resetting the trip data also sets the cadence data
back to zero.
is preset. Once this distance has been cycled, the
next lap is started automatically.
Start the 1
st
lap with
M
. Start all other laps with
C
.
Stop with
M
. Reset with
C
for 3 seconds.
The lap counter is set to 1. The stored lap data can
be recalled under:
B
SETTINGS/SELECT
B
LAP DATA/RECALL
The stored lap data are deleted and overwritten if
lap 1 is started again or 30 laps are exceeded.
4 Installation
4.1 Fitting the transmitter, magnet and handlebar holder >>> P01
Start by fitting the transmitter and magnet.
ATTENTION: The transmitting distance between
the transmitter and the computer on the handle-
bars should not be more than 60 cm (transmission
range).
step 1 Place the rubber pad under the transmitter.
Fit the transmitter on the same side of the fork
where you later want to fit the computer to the
handlebars (right or left) using the cable ties sup-
plied (loose at first, do not pull tight just yet).
ATTENTION: The sensor mark on the transmitter
must point to the spokes.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VDO X3DW cyclecomputing bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VDO X3DW cyclecomputing in de taal/talen: Engels, Pools als bijlage per email.

De handleiding is 2,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van VDO X3DW cyclecomputing

VDO X3DW cyclecomputing Gebruiksaanwijzing - Nederlands - 59 pagina's

VDO X3DW cyclecomputing Gebruiksaanwijzing - Deutsch, English, Français, Italiano - 364 pagina's

VDO X3DW cyclecomputing Gebruiksaanwijzing - Português, Espanôl, Dansk - 59 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info