473886
5
Verklein
Vergroot
Pagina terug
1/39
Pagina verder
X2 VDO CYCLECOMPUTING8
GB SLO PL JP
JP PL SLO GB
www.vdocyclecomputing.com X2 9
NAVIGATOR/SELECT
SELECT shows that there is a submenu for the main
NAVIGATOR menu. You open the submenu with
M
.
B
Set
You can set a starting value here and decide whether
the counter counts forwards or backwards from
this starting value. Further details in Chapter 5.7.
B
Reset
In the reset submenu you set the NAVIGATOR
back to zero. You leave the submenu by pressing
C
again.
STOPWATCH
You can use the stopwatch to measure as many
times as you want. Maximum value: 23:59:59
HH:MM:SS. If the maximum value is exceeded,
the counter starts again at zero.
Start with
M
. Stop with
M
.
Reset with
C
for 3 seconds.
4 Installation
4.1 Fitting the sensor, magnet and handlebar holder >>> P01
When fitting to suspension forks, it is essental to
bear in mind the spring deflection of the forks.
The cable requires an appropriate amount of play.
ATTENTION: Risk of broken cable.
step 1 Place the rubber pad under the sensor. Fit
the sensor on the same side of the fork where you
later want to fit the computer to the handlebars
(right or left) using the cable ties supplied (loose
at first, do not pull tight just yet).
Depending on the room available, the sensor can
be fitted at the front of the fork, inner side of the
fork or backside of the forks. >>> P02
step 2 Place spoke magnet around an outer spoke. The
silver middle of the magnet points towards the sensor.
Align the magnet to the sensor mark with a gap of
about 1 - 5 mm.
step 3 Align sensor and magnet for good and fas-
ten in place: Pull cable ties tight and push magnet
in firmly.
step 4 Install cable from sensor already fitted
along brake cable to the handlebars (fasten with
cable ties supplied) Ideally: Coil sensor cable up
around the brake cable.
step 5 Decide whether fitting to handlebar or
stem and turn the base of the handlebar holder
by 90° accordingly. To do so, undo the screws in
the holder, take out the foot and turn it 90°, insert
and tighten the screws again.
4.2 Installing the battery in the computer >>> P03
Your VDO computer is supplied with a 3V battery
(type 2032).
The battery is already installed when supplied.
To change the battery, proceed as follows:
step 1 Place the battery in the computer casing
with the +terminal facing up.
step 2 Make sure that the battery does not
get wedged.
step 3 Take care that the rubber seal lies flat on
the battery compartment lid.
step 4 Insert the battery compartment lid into the
opening and turn it with a coin to the right as far
as it will go (approx. 1/3 turn).
TIP for changing battery: VDO recommends
changing the battery once a year. Buy a new
battery in good time to ensure the function
works perfectly. When the battery is changed,
all settings and the total kilometres cycled
are saved.
Attention: Do not over tighten screws.
Step 6 Guide the cable ties through the slot in the
handlebar holder, place around the handlebars or
the stem and pull (do not pull tight just yet).
Step 7 If fitting to handlebars: Align computer
angle to achieve optimum readability. Now pull
cable ties tight.
Snip off protruding ends with clippers.
4.3 Placing the computer into the handlebar holder >>> P04
The VDO twist-click system fastens the computer
securely with the handlebar holder.
step 1 Place computer into the holder in 10 o‘clock
position.
step 2 Twist computer to the right to 12 o‘clock po-
sition and click into the holder system.
step 3 To take the computer out, twist to the left
(do not push or pull).
How to remember: Rigid to the Right, Loose to the Left
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

VDO-X2-cyclecomputing

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw VDO X2 cyclecomputing bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van VDO X2 cyclecomputing in de taal/talen: Engels, Pools als bijlage per email.

De handleiding is 1,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van VDO X2 cyclecomputing

VDO X2 cyclecomputing Gebruiksaanwijzing - Nederlands, Português, Espanôl, Dansk - 43 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info