753932
13
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
EN 13
compressor PCPS 10-1100
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Troubleshooting tasks which require the housing to be opened
must only be carried out by an authorized specialist electrical
company or by Trotec.
Light smoke or odour is emitted during the first use:
This is not a fault. These phenomena disappear after a
brief runtime.
The device does not start:
Check the power connection.
Check the power cable and mains plug for damages. If you
notice damages, do not try to take the device back into
operation. To avoid safety hazards, do not perform any
repairs. Send the device to a specialist electrical company
or to Trotec to have the power cable and mains plug
replaced.
Check the on-site fusing.
Check the outside temperature. At temperatures
below+5°C, the motor becomes sluggish and can be
difficult or impossible to start up. Do not use the device at
an temperatures below+5°C.
The device is running but there is no apparent inflation/
The pressure gauge shows no pressure:
Check the valve adapter used for proper fit. Air might be
escaping at the valve of the item to be inflated.
Let the device run for a moment. The pressure will only be
shown on the pressure gauge after the pressure inside the
item to be inflated has exceeded the ambient pressure.
Check the item to be inflated for leaks.
Check the compressed-air gun for proper functioning, and
replace it if necessary.
The device is running but there is no pressure build-up:
The check valve is leaky. Have the check valve inspected
and, if necessary, replaced by a specialist workshop.
Check the seals. Have broken seals replaced by a
specialist workshop.
The device is running but the connected accessories do not
work:
Check the accessories for proper functioning. Replace
defective accessories.
Check the compressed-air hose and the quick coupling,
and have them replaced by a specialist workshop if
necessary.
The device becomes hot:
Note
The device is not suitable for continuous operation.
Over a period of 10minutes, do not use the device for
more than 1.5minutes in continuous operation. Allow
the device to cool down for the remaining time.
Should the device be overheating nonetheless, switch
the device off and disconnect it from the mains.
Allow the device to cool down sufficiently before
switching it back on.
Check whether the device is suitable for the tasks to be
carried out.
Keep the venting slots or air inlet and outlet clear to
prevent the motor from overheating.
Note
Wait for at least 10minutes after maintenance and
repair work. Only then switch the device back on.
Your device still does not operate correctly after these
checks?
Please contact the customer service. If necessary, bring the
device to an authorized specialist electrical company or to
Trotec for repair.
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Trotec PCPS 10-1100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Trotec PCPS 10-1100 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Trotec PCPS 10-1100

Trotec PCPS 10-1100 Gebruiksaanwijzing - Nederlands - 16 pagina's

Trotec PCPS 10-1100 Gebruiksaanwijzing - Deutsch - 17 pagina's

Trotec PCPS 10-1100 Gebruiksaanwijzing - Français - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info