665021
5
Verklein
Vergroot
Pagina terug
1/106
Pagina verder
5
GB
Battery tools use and care
a) Recharge only with charger specified by the manufacturer. A charger
that is sutiable for one type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire
c) When battery pack is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails, screws and other small
metal objects that can make a connection from one terminal to
another. Shorting the battery terminals together may cause a burns or a
fire.
Under abusive conditions, liquid may be ejected from the battery;
avoid contact. If contact accidentally occurs, flush with water. If
liquid contact eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns
WARNING: When used in Australia or New Zealand, it is recommended that
this tool is ALWAYS supplied via Residual Current Device (RCD) with a rated
residual current of 30mA or less.
Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
Additional safety for battery-
operated screwdrivers
For safety relating to protective clothing/equipment and general health hazards
relating to power tools; refer to General and Electrical Safety sections in this
manual
Important: It is imperative to follow all national safety regulations concerning
installation, operation and maintenance
Hold power tools by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring.
Cutting accessory and/or fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live” and give the operator an
electric shock. Do not allow anyone under the age of 18 years to use this
tool, and ensure that operators are qualified and familiar with the operating
and safety instructions
If batteries are to be charged outdoors, ensure that the power supply and
charger are protected against weather/moisture
When using the drill, use safety equipment including safety glasses or
shield, ear defenders, and protective clothing including safety gloves. Wear
a dust mask if the drilling operation creates dust
Use metal and voltage detectors to locate concealed electric, water or gas
lines. Avoid touching live components or conductors
Ensure that the lighting is adequate
Ensure that the drill bit is securely fixed in the chuck. Insecure drill bits can
be ejected from the machine causing a hazard
Ensure that the drill bit is in contact with the workpiece prior to starting up
the tool
Before drilling, check that there is sufficient clearance for the drill bit under
the workpiece
Do not put pressure on the tool, to do so would shorten its service life
Drill bits get hot during operation, allow to cool prior to handling them
Never use your hands to remove sawdust, chips or waste close by the bit
If you are interrupted when operating the drill, complete the process and
switch off before looking up
Where possible, use clamps or a vice to hold your work
Examine the chuck regularly for signs of wear or damage. Have damaged
parts repaired by a qualified service centre
Always wait until the drill has come to a complete stop before putting it
down
Periodically check all nuts, bolts and other fixings and tighten where
necessary
Hold power tools by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring. Cutting
accessory and/or fasteners contacting a ‘live’ wire may make exposed
metal parts of the power tool ‘live’ and give the operator an electric shock.
Battery charger safety
Use the battery charger correctly
Refer to the section of this manual relating to use of the battery charger
before attempting to charge the battery.
Do not attempt to use the charger with any batteries other than those
supplied. Keep your battery charger clean; foreign objects or dirt may
cause a short or block air vents. Failure to follow these instructions may
cause overheating or fire
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard
Examine the battery charger regularly for damage, especially the cord, plug
and enclosure. If the battery charger is damaged, it must not be used until
it has been repaired
Children should be supervised to ensure that they do not play with the
appliance
Warning: Do not recharge non-rechargeable batteries
Use batteries correctly
Only charge batteries using the charger provided. Only use batteries
provided with this power tool, or others recommended by the supplier.
Keep batteries clean; foreign objects or dirt may cause a short. Allow
batteries to cool for 15 minutes after charging or heavy use. Failure to
follow these instructions may cause overheating or fire.
When not in use batteries should be stored at room temperature (approx.
20˚C). Ensure that batteries cannot accidentally short in storage.
WARNING: Li-Ion batteries, if incorrectly used, stored or charged are a fire,
burn and explosion hazard.
Keep the battery out of reach of children
Only charge Li-Ion batteries using the charger provided or designed
specifically for your product
Only use Li-Ion batteries provided with a product or specifically designed to
be compatible
Allow batteries to cool for 15 minutes after charging or heavy use. Failure
to follow these instructions may cause overheating or fire
When not in use batteries should be stored at room temperature
(approximately 20˚C)
Ensure that battery contacts cannot accidentally short in storage. Keep
batteries clean; foreign objects or dirt may cause a short. Keep away from
other metal objects, for example paperclips, coins, keys, nails and screws
Under abusive conditions, liquid may be ejected from the battery. This
liquid may cause skin irritation or burns. Avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, seek medical
help
Do not open, disassemble, crush, heat above 60°C or incinerate. Do not
dispose of in fire or similar
Battery and charger safety features
The battery and charger are fitted with a number of safety features which may
be triggered during charging or operation:
Over-charge protection: Charger automatically switches off when
the battery has reached full charge capacity, protecting the internal
components of the battery
Over-discharge protection: Prevents the battery from discharging beyond
the recommended lowest safety voltage
Over-heat protection: Sensor switches off if the battery becomes too
hot during operation. This can happen if the tool is overloaded or being
used for extended periods of time. Up to 30 minutes cooling time may be
required depending on the ambient temperature
Overload protection: Battery temporarily stops if it is overloaded or the
maximum current draw is exceeded, protecting the internal components.
The battery will resume normal operation when the current draw returns to
a normal safe level. This may take a few seconds
Short circuit protection: The battery will stop working immediately if a short
circuit occurs, this prevents damage to the battery or tool
104207_Z1MANPRO1.indd 5 15/08/2014 10:22
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Triton T12AD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Triton T12AD in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks als bijlage per email.

De handleiding is 5,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info