485614
30
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
5958
Others
3
Remove the lamp cover.
Loosen the screws, then pull up to direction of
the arrow with your fingers on the area shown
in the figure to remove the lamp cover. Be
careful to avoid breaking a nail or otherwise
injuring your fingers when doing so. (If the
screws are too tight to remove the lamp cover,
use any tool.)
4
Pull out the lamp.
Loosen the 2 screws holding the lamp in place,
and pull on the handle to remove the lamp.
5
Mount the new lamp.
Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.
6
Replace the lamp cover.
Align the cover, and press it in, then screw in the
screws loosened in step
3
until the lamp cover is
no longer loose.
7
Reset the lamp timer.
See the lamp’s manual for instructions on resetting
the lamp timer.
Notes and Precautions
Press the button twice to display (a rough guide) of the time of use from the Lamp
time item on the Status display menu.
p.32
As a rule of thumb, it is recommended that the lamp should be replaced after 2,000
hours of use. When Lamp time reaches 2,000 hours, the
icon and a message will
appear. When any operation is performed, the message disappears.
Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the
lamp may fail to come on
p.64
, and the lamp’s lifetime may be shortened.
Always replace the lamp with a new one.
The lamp is made out of glass. Do not touch the glass surface with your bare hands,
bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)
Used Lamps
This projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose it in accordance with local
regulations.
Please read this chapter if the model you purchased includes a PC card slot.
This chapter briefly describes how to use supplied software applications other than the
Wireless utility.
How to use the Projector Configuration Tool
The Projector Configuration Tool is a software utility that allows you to set up the
projector for Infrastructure mode communications using a wireless LAN PC card.
When using this application for the first time, conduct Preparation
p.34
, and start with
the computer in Ad hoc transmission mode.
1
Check MAC address.
The MAC address is a unique address assigned to the wireless LAN PC card.
Display the MAC address on the screen, referring to Displaying Information
p.32
.
Note down the address for future use.
2
Launch the Projector Configuration Tool.
Upon launch, the window shown in the figure to the
right appears on the computer screen.
3
Click on the Browse button.
The computer starts searching for projectors. When it
finds one, Please select is displayed in the
Projector Selection field.
4
Select a projector.
Click on the button for the Projector Selection
field, then from the pull-down list that is displayed,
select
the project with the MAC address you noted down in
step
1
.
When a projector is selected, the computer obtains
information from that projector, and displays the results
in the boxes of the window.
Here, the following is possible:
From the File menu, select Save As..., and save the pre-modification settings on the
computer.
From the File menu, select Open, and apply an existing settings file to the projector.
Lamp replacement (Continued)
2
1
Lamp cover
2
1
1
2
3
4
5
How to use the supplied software
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Toshiba TLP-T701 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Toshiba TLP-T701 in de taal/talen: Nederlands, Engels als bijlage per email.

De handleiding is 3,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info