825268
81
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
81WWW.TORPADO.COM ENGLISH
INTRODUCTION
BIKE SET UPMAINTENANCE
REGULATIONS
WARRANTY SAFETY GENERAL ADVICE
The seatpost bolts must be tightened with the correct torque. Use a torque wrench so you do not
overtighten the bolts. The torque values are outlined in the section entitled MAINTENANCE, 2. Tightening
torques, on the parts themselves and in the instructions provided by the component manufacturers.
Never attach the saddle on the curved section of the saddle rail, but always on the straight sec-
tions.
Check the tightening torque of the seatpost bolts every month against the values indicated in the
section entitled MAINTENANCE, 2. Tightening torques, in the instructions provided and/or on the
components themselves.
2. Integrated saddle locking mechanism with bolts in line
Loosen the bolts at the top of the seatpost with two or three turns, otherwise the whole assembly could
come apart and move the saddle forward or backward, as required. Tighten both the bolts evenly to avoid
changing the angle of the saddle. Tighten the front bolt to lower the front of the saddle; if necessary
loosen the rear bolt. Tighten the rear bolt instead to lower the back of the saddle.
Once you have found the right position, check that
the cross members adhere to the saddle rails before
tightening the bolts with the torque indicated by the
saddle manufacturer. To check that the saddle, that
you have just tightened, does not tilt, put your hand
on the tip and the back of the saddle and press hard
downwards.
Position the saddle so that the seatpost is lamped inside the marked area. If there is no mark, the
mechanism must only be clamped on the straight section and should never be clamped on the front or
rear curved section. Risk of breakage!
If you replace the saddle, remember that saddles are usually designed for seat rails with a 7 mm
diameter. Rails with a different diameter may cause the saddle to break and the rider to fall.
D. HANDLEBARS POSITION AND BRAKE LEVER
Since the bar-ends of a MTB are almost always slightly curved, they need to be adjusted so your wrists
are relaxed and not turned outward too far.
1. Adjusting the position of the handlebars
Release the Allen bolts on the front of the handlebar stem. Loosen the handlebars which can then be
turned to the desired position. Make sure that the handlebars are centred on the handlebar stem and
then, carefully tighten the bolts again with a torque wrench. Follow the correct torque (see GENERAL
RECOMMENDATIONS, 2. Caring for and cleaning your MTB Torpado Impudent).
Follow the tightening torque indicated
81

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Torpado Zenith bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Torpado Zenith in de taal/talen: Engels, Italiaans als bijlage per email.

De handleiding is 2,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info