622632
19
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
FT 92 English
www.toolland.eu 19
4. DETECT GAS LEAKS
To find the gas leak you must brush
soapy water on all the fittings and
connections of the gas circuit. If there is
a leak you will notice bubbles.
If you notice bubbles you must close the
leak.
If there is still a leak after you closed the
leak you must close the gas cylinder
valve and request professional
assistance.
Only check for leaks when the appliance
has cooled down completely.
WARNING! Never use a flame to detect a
gas leak!
5. USE
5.1 PREPARATIONS
Check the appliance for possible transport
damage. Never use a damaged appliance.
Follow all the instructions carefully.
Never place the gas cylinder in front of
the heater. Place the gas cylinder and the
appliance on a stable and level surface.
Always check if the specifications of the
regulator and the hose are the same as
the specifications mentioned on the rating
label.
Take the cabinet on the rear cylinder
cover unscrew of the two fixing screw.
The heater must be used with a regulator
and hose. The flexible hose must be
checked regularly whenever the cylinder
is replaced to be sure it has no scratches
or cuts and that it is in a perfect state. It
must be replaced in any case before the
expiry date stamped on the hose itself.
Connect the flexible tube to the hose
union of the pressure regulator and to
that of the tap, making sure that the
metal bands are tight and paying
particular attention not to tamper with or
damage any component or fitting.
Before connecting the cylinder, make sure
that its tap is closed and that there are
no open flames (lit oven, etc.) in the
place where you are working. Screw the
pressure regulator onto the cylinder,
keeping these warnings in mind:
Check that the gasket seal is in
good condition.
Attach the regulator to the tap,
screwing the nut tightly
counterclockwise.
Carefully check that there is no
gas leaking from the connection
using soapy water: if there is a
leak, bubbles will form; tighten
the connection more or seek
professionally qualified service.
Place the cylinder in its compartment,
taking care that the tube is not twisted or
choked and isn't touching hot parts.
Hook the rear cylinder cover on the
cabinet, insert the two hooks in the
respective holes of the cabinet and put
the wing screws.
To replace the cylinder, make sure that its
tap is closed and that there are no open
flames (lit oven, etc.) or sources of heat
in the place where you are working; we
recommend that you check that the
gasket seals of the regulator and flexible
rubber tube are in good condition and
replace them, if necessary.
To not mishandle the connections or
other components.
Do not turn the cylinder upside down to
completely use its contents: this releases
liquid residues left in the tank that will
irreparably damage the heater.
Do not disconnect the pressure regulator
from the cylinder when the cylinder tap is
open.
The manufacturer will not be responsible
if one of the above points is disregarded.
5.2 START AND STOP
Pos. 1 (Start and Maximum Heating)
Pos. 2 (Medium)
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Toolland FT 92 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Toolland FT 92 in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info