549761
2
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
GB
BABY UNIT
• GETTING TO KNOW YOUR MONITOR
PARENT UNIT
Microphone AC Adaptor jack
Power Indication Light
Power ON/OFF Button
Volume Control Buttons
Sound Level Lights Display
LINK Indication Light
Power Indication Light
Speaker
Sound Activated
Monitoring Light
Sound Activated
Monitoring Button
Power ON/OFF Button
Belt Clip/Battery
Compartment Cover
AC Adaptor Jack
•••
Low Battery on the Parent Unit
Power Indication Light will change
from solid green to ashing red.
Alarm tone on
Parent Unit
Alarm Meaning
Indications on the Parent Unit
Out of range
LINK Indication Light will change
from solid green to ashing red.
(Continuous)
3 beeps
••••••••
Fig.1 Fig.2
Fig.3
PARENT UNIT
Unscrew the battery compartment cover from the back of the unit (N.B: this
may already be supplied loose). Next, link the plug on the end of the battery
pack connector to the socket inside the unit, pushing the plug rmly into
the socket until it clicks. Place the battery pack into the compartment and
screw the cover back into position. See Figure 1.
Ensuring the power cable is correctly connected, plug your Parent Unit into
the mains supply and charge for a full 7 hours. See Figure 2. You can use
your monitor while it is charging by following the ‘SET UP’ guide below.
Important! Your Parent Unit will not function without rst inserting the battery pack.
BABY UNIT
The Baby Unit is powered by your domestic mains supply, using the power adaptor supplied.
Connect the adaptor to the back of the unit as shown in Figure 3.
Position the Baby Unit at least 1 metre away from your baby, ensuring all parts are kept out of
reach. Under no circumstances should you place any parts of the monitor in or on a cot. For
best performance, we recommend that the monitor is placed no further than 3 metres away
from your baby.
• SET UP
POWER ON
Make sure both the Baby and Parent Units are plugged into the mains and that the Parent Unit has its battery pack
installed (see above). The units should stand at least 1 metre apart.
Activate the Baby Unit by pressing and holding the ON/OFF Button
on the back of the unit until the green Power
Indication Light on the front lights up.
Next, activate the Parent Unit by pressing and holding the ON/OFF Button
located on the back (next to the battery
compartment cover) until the green light illuminates.
Note: If the Parent Unit is switched on before the Baby Unit, an out-of-range alarm will sound if the Baby Unit is not
switched on within 30 seconds.
POWER OFF
Switch off the Parent Unit by pressing and holding the ON/OFF Button
until the green light goes out.
Then, press and hold the Baby Unit’s ON/OFF Button
until the light goes out.
• BABY AND PARENT UNIT CONNECTION
As each unit activates, the LINK Indication Light
on the Parent Unit will ash as both Units auto-search and link to
each other. Once a connection is made between Baby and Parent Units, the LINK Indication Light will glow green
constantly and normal monitoring will start. The Sound Level Lights Display reacts to sound: the louder the sound, the
more lights illuminate.
• ALARM MODES
Identify the cause of an audible alarm by using the following table; should you be unable to identify or rectify the
cause of the problem, please refer to the Simple Solution Guide in these instructions.
GB
2
3
2 3
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Tomy Digital SR200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Tomy Digital SR200 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 5,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info