607848
2
Verklein
Vergroot
Pagina terug
1/34
Pagina verder
1
GB
1
5
9
13
17
21
25
29
33
37
41
45
49
53
57
61
1x
1x
1x
ROC
4239
STB
DVD
AUX
TV
C
A
B
CR2032
ROC4238
2
4
6
8
10
12
14
16
18
20
22
24
1
3
5
7
9
11
13
15
17
19
21
23
This universal remote control (4 in 1) is compatible with the majority of television sets, DVD pla-
yers and video recorders, as well as digital boxes such as satellite or cable receivers, DVBT recei-
vers (Digital Video Broadcast Terrestrial), ADSL decoders, and so on.
This remote control was programmed in the factory, so that you can use it to control most of the
sets of the THOMSON group’s make. For this reason, we recommend that prior to attempting to
programme the remote control, you try it out by means of one of the methods described in this
user manual. However, rst of all, please activate the remote control by removing the 2 protective
tabs from the 2 CR 2032 batteries.
Please keep this guide along with the code list (provided separately), so that you can subsequent-
ly programme your remote control for use with other sets.
1: On/Standby or Standby only, depending on
the equipment being used.
2 Mode keys: Select the device to control
(TV, DVD, …).
3 Setup: Allows you to program your remote before
the rst use. It also allows you to access to
secondary functions of certain A/V
appliances (Shift). Press and release the
„Setup“ key followed by the function key you
want.
4 Learn: Used for the learning codes procedure (key
copying) (see page 3).
5: Displays information of the selected
appliance.
6: Teletext On.
7: Teletext Off.
8: Teletext Hold (stop page scrolling).
9 Exit: Turn off the menu of the selected
product.
10 (Mute): Switches the selected appliance sound
off.
11 Menu: Turns on the menu of the selected
product.
12 V-, V+: Increases (+) or decreases (-) the volume
of the selected device.
13 P+, P-: Channel Up and Channel Down buttons.
14: Allow you to navigate the menus
horizontally and verticaly.
15 OK: Conrms a selection.
16 (play): Play a DVD disc (DVD)*.
17: Fast forward (DVD)*.
18 (rewind): Goes backward (DVD)*.
19 (pause): Suspends play and stops on an image*.
20 (record): To record, press the RECORD key twice.
21 (stop): Stop the disc (DVD)*.
22 Numeric keys 0 - 9: These keys have the same
functions as those of your original
remote and are also used to enter the
codes for different products.
23 -/--: In connection with the numeric keys, this
button allows you, with some equipment,
to select directly channels with 2 digits.
24 AV: For selecting an external source (SCART,
HDMI, ...).
* The coloured buttons can be used to select
categories when teletext is activated, and specic
functions depending on the make.
The keys
Testing the remote control before
you programme it
1. Turn on the product you want to control.
2. Press the Mode key that corresponds to the type of
product you want to control:
TV: television set, DVD: DVD player, SAT: satellite
receiver, AUX: any other equipment.
3. Direct the remote control towards your equipment
and try to switch it off by simply pressing the
key G. If the device does not turn off, you must
program the remote control using one of the
methods A, B, C or D described hereafter.
Note 1: Except for the TV key, the DVD, SAT and AUX
mode keys can be programmed to control a device
other than that indicated on the key. It is therefore
possible, for example, to allocate SAT mode to the
DVD key. You must enter the code corresponding to
the manufacturer and the device by using one of the
methods indicated in this manual.
However, method D (automatic search for a code)
will greatly simplify the task for you. In this case it
is only necessary to enter a code from the list that
corresponds to the type of device, for example: 0603
for a Thomson satellite receiver) and then to run the
automatic search procedure. The remote control will
then test all the codes automatically until it nds those
that control the receiver.
Note 2: To control 2 devices of the same type and the
same brand (2 Thomson AUXs, 2 Thomson satellite
receivers, ...) ensure rst that these two devices are
not set to react to the same sub code, they will require
one sub code for one and a different sub code for
the other (i.e., codes A and B with Thomson devices).
Once you have checked this, successively program 2
separate mode keys using method D.
Programming
the remote control
Method A – Fast programming
with 1-digit subcode
Before you start programming, you must nd the
subcode of the set to be controlled. Entering a
subcode lets the remote control test a predened list of
codes. Refer to the list provided with these instructions,
page I of the subcodes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp ashes
to signal that this time is almost up, and then goes
off).
3. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, SAT: satellite
receiver, cable, DVBT, ADSL, AUX: any other
appliance.
4. While the indicator is lit, type in the subcode
(example: 1 for THOMSON).
5.Direct the remote control towards the set and try to
switch it off by pressing the key G.
6.If the set you want to control switches off, press OK
to memorise the code.
7. Should the set not switch off, press key G repeatedly,
until the set switches off. Between two key presses,
leave enough time for the key corresponding to the
selected mode enough time to light up again (about
1 second). Proceeding this way will enable you to
see whether the set responds or not.
8.Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Method B – 4-digit codes
programming
Before you start programming, you must nd the code
of the set to be controlled.
Refer to the list provided with these instructions, page
II of the codes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp ashes
to signal that this time is almost up, and then goes
off).
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thomson ROC4238 4in1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thomson ROC4238 4in1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info