607826
1
Verklein
Vergroot
Pagina terug
1/3
Pagina verder
The ROC 2206 is a universal remote control (2 in 1). It can replace 2 remote controls thanks to its
2 mode keys TV, VCR/DVD... It is compatible with the majority of television sets, video cassette
recorders, DVD players, satellite and cable receivers as well as terrestrial digital television (DVBT),
amplifiers and other audio equipment provided they are controlled by infra red signals.
This remote control has been factory programmed to allow you to use it immediately with the
majority of Thomson Group devices.We therefore advise you to try it before beginning to program it.
If programming is necessary, follow one of the methods A, B, C, D or E that are given in this manual.
But before anything else, fit the two batteries into the remote control handset and peel off the tab as
shown on the diagram on the inside of the cover.
Keep these instructions and the separate list of codes in a safe place so that you can later reprogram
your remote control.
1 I ndicator lamp: the indicator lamp lights up when any
key is pressed.
2 B: On / Standby.
3 R emote control mode
Selects device to control TV, DVD,VCR,...
4 S: programmes the remote control.
SHIFT: activates the secondary key features
(indications in blue).
5 I (EXIT): teletext Off in TV mode.
SHIFT and EXIT: turns off the menu of the
selected product.
6 c: switches the TV sound off.
SHIFT and OK: confirms a selection.
7 VOL-/VOL+ increases (+) or decreases (-) the
volume of the TV set.
SHIFT and VOL-/VOL+ also allows you to
navigate the menus horizontally.
8 M (RECORD): to record (VCR/DVD).
9 F (FF): fast forward *.
10 B (Play): play*.
1 1 K (Pause): stops on an image*.
1 2 Number keys 0 to 9: these keys have the same
functions as those of your original remote and are
also used to enter the codes fo
r
diff
er
ent pr
oducts
.
1 3 AV: for selecting an external source (SCART).
14 Press this key first before you type in the 2-digit
channel number (except for Thomson group
products).
1 5 L (STOP): stop playback*.
1 6 G (REW): goes backward or advances forward*.
17 "Info" key.
Videotext inlay on TV picture.
18 PROG+,PROG-: programmes zapping button
(received by the television set or the satellite
receiver); use to scroll vertically through menus
SHIFT and PROG+/PROG- also allow you to
navigate the menus vertically.
1 9 a (MENU): teletext On/Off in TV mode.
SHIFT and MENU: turns on the menu of the
selected products.
* The coloured buttons can be used to select categories
when teletext is activated, and specific functions
depending on the make.
2 - Te sting the remote control
before programming
1. T urn on the device that you wish to control.
2. P ress the key corresponding (3) to the type of device
to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player.
3. P oint the remote control at the device you wish to
control and try to turn it off using the
B
(2) key.
I f the device does not turn off, you must program the
remote control using one of the methods A, B, C or
D as described below.
1 - Description of keys
3 - Programming
the remote control
Before you start programming, you must find the subcode of
the set to be controlled.
Refer to the list provided with these instructions, page I of the
codes.
1 S witch on the set you want to control.
2. Hold down the S (4) key until the indicator lamp
(1) remains lit (the indicator light remains on for a
few seconds to give you the time to proceed with the
following steps. The indicator lamp flashes when this
time is almost up, and then goes off).
3. P ress the key (3) that corresponds to the type of
equipment you want to control:
TV: television set,
VCR/DVD: video cassette recorder, DVD player.
4. W hile the indicator is lit, type in the subcode (example:
1 for Thomson).
5. D irect the remote control towards the set and try to
switch it off by pressing the
B
(2) key.
6. I f the set you want to control switches off, press
c (6) to memorise the subcode.
7. If the product doesn’t turn off, press the
B
(2)
key repeatedly until the set switches off. Wait
approximately one second between key presses to
give the indicator lamp (1) enough time to go off
and light up again. This will allow you to see whether
the product responds or not.
8. I mmediately upon the switching-off of the set to be
controlled, press c (6) to store the subcode.
Note:
If you want to assign another type of product than those
mentioned on the remote control (with the exception of the
TV button which can only be used to control a television set),
begin by entering the code that corresponds to the product you
want to programme (a 4-digit code that you will find in the code
booklet – see method B).
Example: if you want to control a satellite receiver with the
VCR/DVD key, begin by entering a satellite code (any satellite,
for example: 0603 for a Thomson satellite receiver) then begin
the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands. Check your remote control for proper functioning by
performing the test described on page 3.
Method A – Fast programming with
1-digit subcode
GB
1
01_ROC2206_GB.indd 1 30/11/06 16:56:21
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thomson ROC2206 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thomson ROC2206 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Thomson ROC2206

Thomson ROC2206 Gebruiksaanwijzing - Nederlands - 3 pagina's

Thomson ROC2206 Gebruiksaanwijzing - Deutsch - 3 pagina's

Thomson ROC2206 Gebruiksaanwijzing - Français - 3 pagina's

Thomson ROC2206 Gebruiksaanwijzing - Espanõl - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info