607825
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
GB
1
This universal remote control is compatible with most television sets controlled by infra-red.
This remote control was programmed in the factory, so that you can use it to control most of
the sets of the THOMSON group’s make. For this reason, we recommend that prior to
attempting to programme the remote control, you try it out by means of one of the methods
described in this user manual. However, first of all, you must install 2 batteries (AAA) in the
remote control.
Please keep this guide along with the code list (provided separately), so that you can
subsequently programme your remote control for use with other sets.
1 Indicator light: the red indicator light is lit whenever
a key is pressed.
2 On/Standby or Standby only, depending on the
equipment being used.
3 Activation and use of teletext (Videotext).
4 Selection of channels, input of digital values,
channels with 2 digits, external TV/VIDEO sources
(AV connectors).
5 Programming of the remote control.
6 Mute.
7 Zapping and volume control.
8 Activation and use of menus (display, deletion,
choice, confirmation).
9 Use of teletext (Fastext) or functions specific to
certain devices.
Note:
depending on the actual devices, manufacturers
and year of manufacture, the functions available will
vary.
The keys
Testing the remote control
before programming
Programming
the remote control
1. Switch on the set you want to control.
2. Direct the remote control towards the TV set and try
to switch it off by simply pressing the key
B
B
. If the
device does not turn off, you must program the
remote control using one of the methods A, B, C or
D described hereafter.
Method A – Fast programming
with 1-digit subcode
Method B – 4-digit codes
programming
Before you start programming, you must find the
subcode of the set to be controlled. Entering a sub-
code lets the remote control test a predefined list of
codes. Refer to the list provided with these instructions,
page I of the subcodes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes to signal that this time is almost up,
and then goes off).
3. While the indicator is lit
, type in the subcode
(example: 1 for THOMSON).
4. Direct the remote control towards the set and try to
switch it off by pressing the key
B
B
.
5. If the set you want to control switches off, press OK
to memorise the code.
6. Should the set not switch off, press key
B
B
repeatedly, until the set switches off. Between
pressing the keys, be sure to leave enough time for
the indicator light to go out and then relight (about
1 second). Proceeding this way will enable you to
see whether the set responds or not.
7. Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Before you start programming, you must find the code
of the set to be controlled.
Refer to the list provided with these instructions, page II
of the codes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes to signal that this time is almost up,
and then goes off).
3. While the indicator is lit
, enter the first digit of the
4-digit code proposed for the set to be controlled
(example: 0036 for Thomson).
4. Direct the remote control towards the set and try to
switch it off by pressing the key
B
B
.
5. Should the set not switch off, repeat step 2. Then
type in the next 4-digit code. Try to switch off the set
by pressing key
B
B
once. Repeat this procedure by
trying out each of the 4-digit codes.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Method C – Programming by means
of code retrieval
Should none of the codes work, you still have the
possibility of retrieving the appropriate code without
having to perform any input.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit.
3. Direct the remote control towards the set
and try to
switch it off by pressing the key
B
B
.
4. If the set you want to control switches off, press OK
to memorise the code.
5. Should the set not switch off, press key
B
B
as many
times as required (up to 200 times), until the set
switches off. Between pressing the keys, be sure to
leave enough time for the indicator light to go out
and then relight (about 1 second). Proceeding this
way will enable you to see whether the set responds
or not.
6. Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Try out other remote control keys to find out the range
of functions you can control. If you think that not all of
the keys are active, repeat the procedure of this
programming method to find out the code supporting a
wider range of features.
F01_GB_ROC1407 2/02/07 16:24 Page 1
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thomson ROC1407 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thomson ROC1407 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Thomson ROC1407

Thomson ROC1407 Gebruiksaanwijzing - Nederlands - 2 pagina's

Thomson ROC1407 Gebruiksaanwijzing - Deutsch - 2 pagina's

Thomson ROC1407 Gebruiksaanwijzing - Français - 2 pagina's

Thomson ROC1407 Gebruiksaanwijzing - Espanõl - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info