699750
5
Verklein
Vergroot
Pagina terug
1/90
Pagina verder
5.1 Manual code search
Your Universal Remote Control is equipped with an
internal memory,which is preloaded with up to
350 codes per device type for the most common
TV/STB devices. Youcan zap through these codes
until the device you want to control shows a
reaction. This might be that the device you want to
control switches off (POWER key) or changes the
channel (CH+/CH- keys).
5.1.1 Turn on the device you want to control
5.1.2 Press and hold the device button which you
want to control (e.g. TV) for 3seconds until
the LED is on.
5.1.3 Press the “POWER” or the CH+/CH- key to
zap through the preloaded codes until the
device you want to control reacts.
5.1.4 Press MUTE to save the code and exit the
code search. The LED indicator turns off.
Note
Internal memory limitations allow only up to 350
most common device codes to be preloaded.
Due to the extensive number of different availa-
ble TV/STB devices on the market, it may be pos-
sible that only the most common main functions
areavailable. If so, repeat steps 5.2.1 to 5.2.5 to
nd amorecompatible code. No code may be
available for some special device models.
5.2 Auto Code Search
Auto Code Search uses the same preloaded codes
as the Manual Code Search (5.2) but your Universal
Remote Control scanns through the codes automa-
tically until the device you want to control shows
areaction. This might be that the device you want
to control switches off (POWER key) or changes the
channel (CH+/CH- keys).
5.2.1
Turn on the device you want to control.
5.2.2 Press and hold the device button which
you want to control (e.g. TV) until the LED
indicator ash once and then keep on.
5.2.3 Press the CH+/CH- keys or POWER to start
the Auto Code Search. The LED indicator
ashes once followed by permanent light.
The Universal Remote Control has alatency of
6seconds beforethe rst scan starts.
Note: Scan Speed Settings
Scan Speed Settings can be set at either 1or
3seconds. The default setting for the scan
time per single code is 1sec. If this feels un-
comfortable ,you can switch to 3sec. scan
time per single code. To switch between the
scan times, press CH+ or CH- during the
6sec. latency beforeAuto Code Search starts
scanning.
5.2.4 The LED indicator conrms each single code
scan with asingle ash.
5.2.5 Press MUTE to save the code and exit the
code search. The LED indicator turns off.
Note
When all codes aresearched without suc-
cess, the Universal Remote Control exits
Auto Code Search and returns to operational
mode automatically.Currently stored code
is not changed.
5.3 Code Identification
The Code identication offers you the possibility,to
determine an already entered code.
5.3.1 Press and hold the device button until the
LED indicator ash once and then keep on.
5.3.2 Press button ”AV” two times.
5.3.3 LED indicator ashes times means the code.
Like code 1234, LED indicator will ash once
and pause approx.2s, ash two times and
pause approx.2s, ash 3times and pause
approx.2s, then ash 4times and pause
approx.2s. (Number 0and number 1both will
ash once, but number 0will ash very fast).
3
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Thomson-ROC-Z107

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thomson ROC Z107 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thomson ROC Z107 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 1,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info