771163
49
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
43
EN
Trouble Shooting
Problems
Check
The screen of the
control panel does not
turn on.
Make sure the switch on the back or on the side of the device is in
position I.
Make sure the device is connected to the electrical system.
The device is not
heating.
If the device is in programming mode, make sure the programming
in set at COMFORT.
Make sure the circuit breakers of the system are activated or that the load
shedder (
if you have one
) did not out powered the heater.
If the temperature of the room is higher than the set temperature, it is
normal the device is not heating.
The device is heating
all the time.
Make sure the device is not located near an air stream or
the set temperature was not increased.
The device is not
heating enough.
Increase the Comfort set temperature.
If it is set at the maximum temerature, check the following:
- Check if another heating mode exists in the room.
- Make sure your device is only heating the room (closed door).
- Have the power supply to the device checked.
- Check if the power of your device is adapted to the size of your room
(
we recommend an average of 100 W/m2 for a ceiling height of 2,50m or
40W/m3
).
The surface of the
device is very hot.
It is normal for the device to be hot when in use. The maximum surface
temperature is limited according to the NF Electricity Performance
Standard. However, if you feel that your device is still too hot, make sure
the power is adapted to the size of your room (
we recommend 100W/m²
for a ceiling height of 2,50m or 40W/m3
) and that the device is not placed
near an air stream which would affect its control mechanism.
Dirty marks appear on
the wall around the
device.
The dirty marks come from the bad quality of the air in the room. In this
case, you are advised to check that the room is correctly aired (
ventilation,
vent duct, etc.
), that the air is clean and not to smoke in the room. Your
device will not be replaced under guarantee because of these dirty marks.
The Expert Menu is
not accessible.
You saved a PIN. You must enter your PIN to access the Expert Menu
(see Expert menu section).
The device does
not follow internal
programming
commands.
Check the set date and time.
Make sure the device is in PROG MODE and internal programming is
selected.
The device does
not follow external
programming
commands.
Make sure the programming unit is used properly (see the operating
instructions of the Control Unit). Make sure the device is in PROG
MODE and the external control is selected.
If you were not able to solve your problem, contact a professional with
your device references found on the nameplate (
commercial code (C
),
commercial code (C
commercial code (C
serial No. (E))
, room temperature and maybe the programming system
references. You may also have to provide information contained in the
Information Part of the Expert Menu.
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Thermor Emotion 4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Thermor Emotion 4 in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 4.79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info