636740
13
Verklein
Vergroot
Pagina terug
1/17
Pagina verder
13
Adjusting the idle speed
First, check that the air filter is clean, as it can effect the
result.
When the idle speed is correct, the cutting blade should
not mowe, when machine is idling.
If adjustment is required, the idle screw (1) can be
adjusted. See Fig. 16,
Follow below procedure:
1. Close (turn counter clockwise) the idle adjustment
screw, with the engine running, until the cutting
attachment starts to rotate.
If the ildle speed cannot be adjusted so that the cutting
blade stops mowing. Contact your dealer/service
center. Do not use the machine until it has been
correctly adjusted or repaired.
Adjusting engine speed
Engine speed can be adjusted by following below
procedure (Fig. 19):
4. Adjust the screw (1). Opening 1 ± 1/4
5. Turn counter clockwise (2) decreases speed
6. Turn clockwise (3) increases the speed.
It is recommended to let a authorized service center
adjust the engineed speed.
Fuel filter
When the engine runs short of fuel, check the fuel cap
and the fuel filter for blockage/dirt, and clean it before
new mixed fuel is added. See Fig. 17.
Technical specifications
Model HTP 2200
Engine 22.2 cc / 0.68 kW
Rotations per minut Max 10,000 rpm (no-load)
Bar length 60 cm
Cutting length 55 cm
Cutting width 28 mm
Fuel tank 0.44 liter
Weight 5.6 kg
Noise 107 dB(A)
Standard warranty terms and conditions
The warranty period is 2 years for private end users in
EU countries.
Products sold for commercial use, only have a warranty
period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are
NOT covered by the warranty.
Wearing parts, which are NOT covered for more than
12 months:
Knives/blade
Cables
Switches
Membranes/gaskets
Spark plugs
Engine liquids (oil, gasoline, grease)
Starter cords
Filters
If you start the engine without adding correct fuel mix of
gasoline and 2-stroke oil, it will be damaged and cannot
be repaired and therefore not covered by the warranty.
The warranty does NOT cover damages/faults
caused by:
Lack of service and maintenance
Structural changes
Exposure to unusual external conditions
Damages to the bodywork, deck, handles, panels
etc.
If the machine has been improperly used or
overloaded
Wrong use of oil, gasoline, grease or other liquid
types, which are not recommended in this user
manual
Bad or dirty gasoline, which results in
contamination of the fuel system
Use of unoriginal spare parts.
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is
determined in each case by an authorized service
center.
Your receipt is your warranty note, why it should
always be kept safe.
REMEMBER: The purchase of spare parts as well as
any request for warranty repair, model number, year
and serial number should always been informed. It can
be found on the CE-label on the machine!
* We reserve the right to change the conditions and
accept no liability for any misprints
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Texas HTP 2200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Texas HTP 2200 in de taal/talen: Engels, Deens als bijlage per email.

De handleiding is 4,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info