627194
7
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
- 7 -
5. INSTALLATION
WARNING! CARRY OUT ALL INSTALLATION
OPERATIONS AND ELECTRICAL CONNECTIONS WITH THE
WELDING MACHINE COMPLETELY SWITCHED OFF AND
DISCONNECTEDFROMTHEPOWERSUPPLYOUTLET.
THE ELECTRICAL CONNECTIONS MUST BE MADE ONLY AND
EXCLUSIVELY BY AUTHORISED OR QUALIFIED PERSONNEL.
PREPARATION
Unpack the welding machine, assemble the separate parts contained
in the package.
Assembling the return cable-clamp
Fig. E
Assembling the welding cable-electrode holder clamp
Fig. F
HOWTOLIFTTHEWELDINGMACHINE
All the welding machines described in this handbook should be lifted
using the handle or strap supplied if provided for the particular model
(tted as described in FIG. L).
POSITIONOFTHEWELDINGMACHINE
Choose the place to install the welding machine so that the cooling
air inlets and outlets are not obstructed (forced circulation by fan,
if present); at the same time make sure that conductive dusts,
corrosive vapours, humidity etc. will not be sucked into the machine.
Leave at least 250mm free space around the welding machine.
WARNING! Position the welding machine on a at
surface with sufcient carrying capacity for its weight, to
prevent it from tipping or moving hazardously.
CONNECTIONTOTHEMAINPOWERSUPPLY
- Before making any electrical connection, make sure the rating
data of the welding machine correspond to the mains voltage and
frequency available at the place of installation.
- The welding machine should only be connected to a power supply
system with the neutral conductor connected to earth.
- To ensure protection against indirect contact use residual current
devices of the following types:
- Type A (
) for single phase machines;
- Type B (
) for 3-phase machines.
- To comply with the requirements of the EN 61000-3-11 (Flicker)
standard we recommend connecting the welding machine to
interface points of the power supply that have an impedance of
less than:
Zmax = 0.47 ohm (80A).
Zmax = 0.24 ohm (130A - 170A).
Zmax = 0.17 ohm (200A).
- the welding machine does not fall within the requisites of IEC/EN
61000-3-12 standard.
Should it be connected to a public mains system, it is the installer’s
responsibility to verify that the welding machine itself is suitable
for connecting to it (if necessary, consult the distribution network
company).
- Unless otherwise specied (MPGE), the welding machines are
compatible with power generating sets for voltage oscillations up
to ± 15%.
For correct use, the power generating set must be brought to
steady conditions before being able to connect the inverter.
- PLUG AND OUTLET:
- The 230V model is tted at the factory with a power supply cable
and normalised plug, (2P + T) 16A/250V .
It can therefore be connected to a mains outlet tted with fuses
or an automatic circuit-breaker; the special earth terminal should
be connected to the earth conductor (yellow-green) of the power
supply line.
Table (TAB.1) shows the recommended delayed fuse sizes in
amps, chosen according to the max. nominal current supplied by
the welding machine, and the nominal voltage of the main power
supply.
- For welding machines without a plug (115/230V models),
connect a normalised plug (2P + T) - having sufcient capacity-
to the power cable and prepare a mains outlet tted with fuses
or an automatic circuit-breaker; the special earth terminal should
be connected to the earth conductor (yellow-green) of the power
supply line. Table (TAB. 1) shows the recommended delayed
fuse sizes in amps, chosen according to the max. nominal current
supplied by the welding machine, and the nominal voltage of the
main power supply.
WARNING! Failure to observe the above rules will
make the (Class 1) safety system installed by the manufacturer
ineffective with consequent serious risks to persons (e.g.
electricshock)andobjects(e.g.re).
CONNECTIONOFTHEWELDINGCABLES
WARNING! BEFORE MAKING THE FOLLOWING
CONNECTIONS MAKE SURE THE WELDING MACHINE IS
SWITCHED OFF AND DISCONNECTED FROM THE POWER
SUPPLY OUTLET.
Table (TAB. 1) gives the recommended values for the welding cables
(in mm
2
) depending on the maximum current supplied by the welding
machine.
MMAWELDING
Almost all coated electrodes are connected to the positive pole (+)
of the power source; as an exception to the negative pole (-) for acid
coated electrodes.
WELDINGOPERATIONSWITHDIRECTCURRENT
Connecting the electrode-holder clamp welding cable
On the end take a special terminal that is used to close the uncovered
part of the electrode.
This cable is connected to the terminal with the symbol (+).
Connecting the welding current return cable
This is connected to the piece being welded or to the metal bench
supporting it, as close as possible to the join being made.
This cable is connected to the terminal with the symbol (-).
Warnings:
- Turn the welding cable connectors right down into the quick
connections (if present), to ensure a perfect electrical contact;
otherwise the connectors themselves will overheat, resulting in
their rapid deterioration and loss of efciency.
- The welding cables should be as short as possible.
- Do not use metal structures which are not part of the workpiece
to substitute the return cable of the welding current: this could
jeopardise safety and result in poor welding.
6.WELDING:DESCRIPTIONOFTHEPROCEDURE
- It is most important that the user refers to the maker’s instructions
indicated on the stick electrode packaging. This will indicate the
correct polarity of the stick electrode and the most suitable current.
- The welding current must be regulated according to the diameter of
the electrode in use and the type of the joint to be carried out: see
below the currents corresponding to various electrode diameters:
Ø Electrode (mm)
Weldingcurrent(A)
min. max.
1.6 25 50
2 40 80
2.5 60 110
3.2 80 160
4 120 200
- The user must consider that, according to the electrode diameter,
higher current values must be used for at welding, whereas for
vertical or overhead welds lower current values are necessary.
- As well as being determined by the chosen current intensity, the
mechanical characteristics of the welded join are also determined
by the other welding parameters i.e. arc length, working rate and
position, electrode diameter and quality (to store the electrodes
correctly, keep them in a dry place protected by their packaging or
containers).
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Telwin FORCE 165 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Telwin FORCE 165 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 4,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info