679709
4
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
For optimal WLAN performance attach both of the
supplied antennas to the device.
V. 2.0 - 20150223 - 5500001785
Info
LEDs
System requirements
Automatic configuration
ISDN connection
Select operating mode
Side view
Scope of supply
LEDs back view
1
Status Green
2
Service Yellow
The LEDs are linked to those on the top of the
device and show the identical behavior.
Mounting Brackets
Due to the position of the devices in a rack it is recommended to use remote antenna. Attach
the mounting brackets to the device using the supplied screws.
The mounting brackets and screws are available as an accessory (Part No. MN40285514).
During operation in a rack the ambient temperature must not exceed 40° C.
Software Update
Antenna connector
WLAN
First-time use of the Premium Digitalisierungsbox
Automatic configuration is a service for Telekom customers that you can use with your
Digitalisierungsbox.
Connect the Digitalisierungsbox to the mains. Connect the cables to the appropriate sockets/
jacks. Wait until the Service LED goes out.
Start an Internet browser, enter telekom.de in the address bar and confirm with the Return key.
You are redirected to the Telekom autoconfiguration page. Enter your access ID and your
password and click on Start Configuration. During automatic configuration, the Service LED
will light up.
Wait until a confirmation is displayed that the configuration has been successful. The Service
LED is no longer lit now.
If the Telekom webpage does not open, first check all cabling.
For the configuration of the device, the following system requirements must be met:
 Operating system Microsof
t Windows XP SP3 or later; Windows XP SP3 requires the following
hotfix: http://support.microsoft.com/kb/953761
 Internet Explorer version 7 or 9 or later (the security settings may need to be adjusted),
Mozilla Firefox version 4 or later, Chrome
 Installed network card (Ethernet)
 Installed TCP/IP protocol
 PC configured to automatically obtain IP address and DNS server
 High colour display (more than 256 colours) to show graphics accurately
Case 1: If the p
assword has not yet been changed, you can select the operating mode once
you log in.
Case 2: If the password has been changed, the device has been configured as a telephone
system ex works.
You can also change operating mode in the menu Assistants Ô First Steps Ô Operating
Mode. Note that some features will not then be available. Assembly and the basic configuration
are exactly the same.
If you switch from telephone system to media gateway or from media gateway to
telephone system, the device does a factory reset.
This means that the device reverts to condition it was in when it was supplied.
The configuration is deleted and all the passwords are reset.
Premium Digit
alisierungsbox
 One Ethernet LAN cable (yellow)
 One Ethernet WAN cable (blue)
 One DSL cable (black)
 Two connector cables analogue terminals (grey)
 Power supply unit
 Two Wi-Fi antennas
 Installation poster
 Safety instructions
The switches for terminating the ISDN interfaces can be found on the bottom / in the lower
housing. Both switches are set to ON ex works. This means that termination is enabled and
the device is preconfigured for the operation of all common applications.
The device is delivered with the system software version which is current at the time of
production. The system software is continually being upgraded to improve the security and
functionality of the device. When you first start the device, you may be prompted to update the
software. If you have access to Telekom's automatic configuration, the system software for
your device will automatically be updated to the latest version.
Alternatively, you can update the software in the User view. To use this option to update the
system, you require a functioning Internet connection.
Under Firmware Update, click Update to start the process.
Do not interrupt either the power supply or the internet connection.
Whenever new system software has been installed, you need to restart the device.
Should an error occur during the update process, do not restart the device and contact
customer service.
You can call the free numbers 0800 330 1300 or 0800 330 2870 (for corporate clients) during
normal business hours for any further advice on your Digit
alisierungsbox.
You can also find more information online at http://hilfe.telekom.de.
If you think your connection may be faulty, please call Technical Customer Service free
of charge at the respective number above, or refer to http://hilfe.telekom.de.
Please read the user guide before connecting the device or starting it up!
Reset
The reset is performed by using the reset button at the terminal area.
The device is rebooted by quickly pressing the key (ca. one second). Pressing the key is equivalent
to an interruption of the power supply. Saved data are preserved, but all connections are interrupted.
If you press the reset key for approx. 30 seconds, the device performs a factory reset. This means
the device is returned to its ex works state. Connection data for incoming and outgoing phone calls
are preserved. The configuration is deleted and all passwords are reset.
The reset has finished once the status LED flashes continuously again after approx. 30 seconds.
LED Colour Status Information
Service Yellow on Undergoing automatic maintenance
off No automatic maintenance
Mem. off Memory is ready for read/write accesses
Green flickering Read/write access
WLAN off WLAN or all assigned wireless networks disabled
Green slow Wireless network is enabled, no client is logged in
flashing
Green flashing Wireless network is enabled, at least one client is logged in
quickly
Green flickering Wireless network is enabled, at least one client is logged in,
there is some data traffic
DSL Green on Connection established
Green slow Synchronisation running
flashing
off No synchronisation
Green flickering Data transfer
TEL Green on Telephony ready at IP connector (Voice over IP)
off Telephony not configured
ISDN1/2 Green on ISDN telephone system connected
off On standby or not functioning
Status Green on After switching on: Device is started
While operating: Fault
Green slow The device is active
flashing
Power Green on The power supply is connected
off No power supply
ON
OFF
21
PowerStatusWLAN DSLMem. TEL ISDN1 ISDN2Service
Reset
1
2
DSL LAN1 LAN2 LAN3 LAN4 LAN5 ISDN1 ISDN2 a/b1 a/b2 a/b3 a/b4
Reset
1
2
LED Colour Status Information
LAN 1  4 (Link/Act) Green On Ethernet connection established
(Link/Act) Green Flashing Data transmission via Ethernet
(Link/Act) Off No Ethernet connection
(Speed) Green On 1000 Mbit/s transfer rate
(Speed) Orange On 100 Mbit/s transfer rate
(Speed) Off 10 Mbit/s transfer rate
LAN 5 (Link/Act) Green On WAN-Ethernet connection established
(Link/Act) Green Flashing Data transmission via ETH 5
(Link/Act) Off No Ethernet connection
(Speed) Green On 1000 Mbit/s transfer rate
(Speed) Orange On 100 Mbit/s transfer rate
(Speed) Off 10 Mbit/s transfer rate
The LEDs for the Ethernet sockets LAN-4 (LAN) and LAN5 (WAN) show the following status information:
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Telekom Digitalisierungsbox Premium bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Telekom Digitalisierungsbox Premium in de taal/talen: Duits als bijlage per email.

De handleiding is 7,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Telekom Digitalisierungsbox Premium

Telekom Digitalisierungsbox Premium Installatiehandleiding - Deutsch - 114 pagina's

Telekom Digitalisierungsbox Premium Aanvulling / aanpassing - Deutsch - 7 pagina's

Telekom Digitalisierungsbox Premium Gebruiksaanwijzing - Deutsch - 456 pagina's

Telekom Digitalisierungsbox Premium Gebruiksaanwijzing - Deutsch - 303 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info