640531
12
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
10
EN
sharpened.
- Block again with the handle M19 and sharpen.
24. SHARPENING THE DEPTH GAUGE (FIG. 20)
- The depth of the depth gauge normally needs restoring
after the cutter has been sharpened 2 or 3 times. To do
this, grind material from the depth gauge itself using an
appropriate at le (not supplied with the machine).
- Check if the gauge depth is correct, using the template
with the shape related to the type of chain used. Please
also consult the chain table, (column F).
25. STOPPING AND SHUTTING DOWN
25.1 STOPPING
Unplug the power cable from the mains.
25.2 SHUTTING DOWN
Once you have nished using the machine, disconnect it
and clean it thoroughly.
Store it in a dry and safe place, protected against dust and
damp.
25.3 ROUTINE MAINTENANCE
Follow the instructions given in the “STOPPING”
section before you start to work on the machine.
Maintenance interval Job
When the grinding wheel
reaches a minimum diameter
of approximately 85 mm
(3.34 in)
Replace the grinding wheel.
40 hours
Clean the grinder thoroughly
using a rag or a cleaning
brush.
Do not use compressed air.
25.4 HANDLING AND TRANSPORT
- If you need to transport the machine, take it off the bench
or wall, dismantle the grinding wheel and put all the parts
in a packing box to protect them against impact.
25.5 DEMOLITION AND DISPOSAL
The machine is to be demolished by qualied personnel
in compliance with current laws in force in the country in
which it is installed.
The symbol
(on the rating nameplate) points out that
the product must not be disposed of with normal household
garbage. Contact an authorized service centre or your dealer
for disposal instructions.
Before you scrap the machine, make it unusable (by
cutting the power supply cable for example) and make
the parts safe, which could cause a source of danger
for children if they should play with the machine.
26. TROUBLE SHOOTING
Follow the instructions given in the “STOPPING”
section before you start to work on the machine.
- Contact a  if you are still unable to
restore the correct operation of the machine following the
instructions given in the chart.
 Probable cause Solution
The machine fails
to start when you
press the switch.
The thermal
switch has
tripped.
Wait for the motor
cooling down and
for the device rset.
One of the safety
devices of the
system to which
the machine is
connected has
tripped (fuse, cir
-
cuit breaker etc.)
Reset the safety
device.
The machine is not
plugged into the
mains properly.
Unplug and plug in
again properly.
The machine
vibrates abnormally.
The machine is not
secured correctly.
Check it is secured
properly and, if
necessary, tighten
the securing
screws correctly.
The vise unit is not
secured correctly
to the base unit.
Tighten the related
blocking handle
correctly.
The grinding
wheel is not tted
correctly in its seat
on the hub.
Dismantle the
grinding wheel,
check its integrity
and fit it again
correctly.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Tecomec Speed Master bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Tecomec Speed Master in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info