622563
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
Istr-trony-6 cod-eng GMT S2 Pag. 2
di 2
Note:
To activate/modify the second personal code you shall always program the first one again.
5. RESETTING CODES
Is possible cancel the personal codes pressing the “button PROGRAMMING” and the “ON” button for 5 sec.
The first code goes on 111111 and the second code will be deactivated.
Note:
If errors have been made while setting your new code, this will be indicated by the red “ERRORLED lighting up and a beep.
Proceed in that case, a new and correct their own personal code by repeating the steps under item 4.
In memory was previously the code set to error (a new safe “111111”).
Before closing the safe, it is recommended to carry out a door open, some evidence of initiation using its personal
code.
6. OPENING THE SAFE USING YOUR PERSONAL CODE
Press “ON”
Enter your personal code set earlier and press “ENTER”. The green “OK” LED lights up for five seconds. Within this time,
turn the knob clockwise and open the door.
7. SIGNAL INDICATING THAT INTERNAL BATTERIES ARE GOING FLAT
When the internal batteries begins to go flat, this is indicated at the end of the opening procedure, by the red “BATTERY LED
lighting up and a low beep tone. At this point, it will still be possible to open the safe a number of times. Replace the internal
ALKALINE batteries.
8. EMERGENCY OPENING WITH INTERNAL BATTERIES FLAT
If the failing batteries goes completely flat, as soon as the keyboard is pressed, to proceed with opening the safe:
It is necessary to use a new 9V LR61 alkaline battery externally (see Pic. 2);
Press the 9V battery contacts firmly on the corresponding contacts on the keyboards, ensuring that they are positioned
correctly (the “-“ of the battery touching the bigger contact and the “+” of the battery touching the small contact);
Press “ON” and enter your personal code, followed by the key “ENTER”;
Turn the knob clockwise to open the door.
9. ONLY VERSIONS WITH EMERGENCY KEY:
OPENING WITH EMERGENCY KEY
Remove the adhesive label marked with the letter “E(Pic.3);
Insert the key and open the lock up to the stop point, turn the knob clockwise and open the door;
By holding the door open, turn the knob until the emergence of full bolts and remove the key after rotated counter clockwise.
To replace the label E;
Note: If the opening with key emergency is necessary for the oversight of their own personal code, you must store a new code
following the instructions at point 4.
IMPORTANT !
Should replace the batteries once a year
Even new batteries may be defective or short-term. Therefore, in the event of a malfunction of the electronic system,
ensuring, first of all, to replace the internal batteries.
The manufacturer assumes no liability for non-compliance with the instructions or improper use of safe (penalty decay of
the guarantee).
CONTACTS
FOR
EXTERNAL
BATTERY
Pic. 2
STICKERS
KEY FOR
EMERGENCY
Pic. 3
Detail of the sliding closing to
protect the PROGRAMMING key
BATTERY CASE
Pic. 1
SCREW TO BE
REMOVED
In the smallest models the
PROGRAMMING key is
on the top.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Technomax ST vanaf 2009 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Technomax ST vanaf 2009 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Technomax ST vanaf 2009

Technomax ST vanaf 2009 Gebruiksaanwijzing - Nederlands - 2 pagina's

Technomax ST vanaf 2009 Gebruiksaanwijzing - Français - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info